[mythtv-users] Capture Problems (Leadtek Winfast 200XP Deluxe)

listman listman at depfyffer.com
Sat Oct 16 20:55:42 UTC 2004


Are you in the US - NTSC? are most of your channels off by one and in
B&W?
If so you might have to recompile your kernel, Thats what I had to do,
this also allowed the remote to work.


On Sat, 2004-10-16 at 12:28, Brad Bonkoski wrote:
> I have some video going.  It is the deluxe model.  I think it was just a 
> configuration option on the back-end.
> Although the picture is choppy!  Is there any more performance tuning I can 
> do to clean this up?
> My system is an AMD2600+ and 512MB of ram, nVidia 5200FX GFX card.
> 
> Also the sound is not coming through, still have some more investigation to 
> go through, but if anyone has any gotchas and/or tips they could share I 
> would appreciate it.
> 
> Thanks!
> -Brad
> 
> ----- Original Message ----- 
> From: "nate s" <nate.strickland at gmail.com>
> To: "Discussion about mythtv" <mythtv-users at mythtv.org>
> Sent: Saturday, October 16, 2004 3:16 PM
> Subject: Re: [mythtv-users] Capture Problems (Leadtek Winfast 200XP Deluxe)
> 
> 
> >I believe I have the same card as you.
> >
> > For bttv vs cx88, it depends on what card you have; the delux is bttv,
> > the expert is cx88.
> >
> > Does video work in tvtime or xawtv?
> >
> > -Nate
> >
> >
> > On Fri, 15 Oct 2004 15:54:03 -0400, Brad Bonkoski
> > <bbonkosk at tampabay.rr.com> wrote:
> >>
> >> I have read some general discussion about using the bttv driver versus 
> >> the
> >> ct8xx driver.  Currently I have had the best 'apparent' luck with the 
> >> bttv
> >> driver.  Here is my dmesg output:
> >> server root # dmesg  | grep bttv
> >> bttv: driver version 0.9.15 loaded
> >> bttv: using 8 buffers with 2080k (520 pages) each for capture
> >> bttv: Bt8xx card found (0).
> >> bttv0: Bt878 (rev 17) at 0000:02:07.0, irq: 9, latency: 32, mmio: 
> >> 0xde000000
> >> bttv0: detected: Leadtek WinFast TV 2000 [card=34], PCI subsystem ID is
> >> 107d:6606
> >> bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP [card=34,insmod 
> >> option]
> >> bttv0: gpio: en=00000000, out=00000000 in=00bf7707 [init]
> >> bttv0: using tuner=2
> >> bttv0: i2c: checking for MSP34xx @ 0x80... not found
> >> bttv0: i2c: checking for TDA9875 @ 0xb0... not found
> >> bttv0: i2c: checking for TDA7432 @ 0x8a... not found
> >> bttv0: registered device video0
> >> bttv0: registered device vbi0
> >> bttv0: registered device radio0
> >> bttv0: PLL: 28636363 => 35468950 .. ok
> >> bttv0: add subdevice "remote0"
> >> bttv0: PLL can sleep, using XTAL (28636363).
> >>
> >> Does this look like the device driver is being properly loaded, and the
> >> device properly registered?
> >> When I run myth and try to watch TV, I just get a green screen and 
> >> nothing
> >> else.
> >> Any ideas on where to start.
> >>
> >> Thanks
> >> -brad
> >> _______________________________________________
> >> mythtv-users mailing list
> >> mythtv-users at mythtv.org
> >> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
> >>
> >>
> >>
> >
> 
> 
> --------------------------------------------------------------------------------
> 
> 
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
> 
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users



More information about the mythtv-users mailing list