[mythtv-users] Capture Problems (Leadtek Winfast 200XP Deluxe)

[Brad Bonkoski]

I have some video going.  It is the deluxe model.  I think it was just a 
configuration option on the back-end.
Although the picture is choppy!  Is there any more performance tuning I can 
do to clean this up?
My system is an AMD2600+ and 512MB of ram, nVidia 5200FX GFX card.

Also the sound is not coming through, still have some more investigation to 
go through, but if anyone has any gotchas and/or tips they could share I 
would appreciate it.

Thanks!
-Brad

----- Original Message ----- 
From: "nate s" <nate.strickland at gmail.com>
To: "Discussion about mythtv" <mythtv-users at mythtv.org>
Sent: Saturday, October 16, 2004 3:16 PM
Subject: Re: [mythtv-users] Capture Problems (Leadtek Winfast 200XP Deluxe)


>I believe I have the same card as you.
>
> For bttv vs cx88, it depends on what card you have; the delux is bttv,
> the expert is cx88.
>
> Does video work in tvtime or xawtv?
>
> -Nate
>
>
> On Fri, 15 Oct 2004 15:54:03 -0400, Brad Bonkoski
> <bbonkosk at tampabay.rr.com> wrote:
>>
>> I have read some general discussion about using the bttv driver versus 
>> the
>> ct8xx driver.  Currently I have had the best 'apparent' luck with the 
>> bttv
>> driver.  Here is my dmesg output:
>> server root # dmesg  | grep bttv
>> bttv: driver version 0.9.15 loaded
>> bttv: using 8 buffers with 2080k (520 pages) each for capture
>> bttv: Bt8xx card found (0).
>> bttv0: Bt878 (rev 17) at 0000:02:07.0, irq: 9, latency: 32, mmio: 
>> 0xde000000
>> bttv0: detected: Leadtek WinFast TV 2000 [card=34], PCI subsystem ID is
>> 107d:6606
>> bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP [card=34,insmod 
>> option]
>> bttv0: gpio: en=00000000, out=00000000 in=00bf7707 [init]
>> bttv0: using tuner=2
>> bttv0: i2c: checking for MSP34xx @ 0x80... not found
>> bttv0: i2c: checking for TDA9875 @ 0xb0... not found
>> bttv0: i2c: checking for TDA7432 @ 0x8a... not found
>> bttv0: registered device video0
>> bttv0: registered device vbi0
>> bttv0: registered device radio0
>> bttv0: PLL: 28636363 => 35468950 .. ok
>> bttv0: add subdevice "remote0"
>> bttv0: PLL can sleep, using XTAL (28636363).
>>
>> Does this look like the device driver is being properly loaded, and the
>> device properly registered?
>> When I run myth and try to watch TV, I just get a green screen and 
>> nothing
>> else.
>> Any ideas on where to start.
>>
>> Thanks
>> -brad
>> _______________________________________________
>> mythtv-users mailing list
>> mythtv-users at mythtv.org
>> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
>>
>>
>>
>


--------------------------------------------------------------------------------


_______________________________________________
mythtv-users mailing list
mythtv-users at mythtv.org
http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users