[mythtv-users] Pvr-250 refuses channel change

[Ali Asad Lotia]

I must admit, that I am using the 0.3.7k driver, so I am not as
familiar with the 0.2 series. What fixed it for me was to:

do a make menuconfig in /usr/src/linux

go into the device drivers section and from there to the i2c support section
go into the other i2c chip support and check to see if you have
"EEPROM reader" set to be compiled into the kernel. If that is the
case, then either unselect it or compile it as a module and make sure
that the module is loaded into your kernel after the tveeprom module.

hope this helps.

--
ali asad

On 9/2/05, Scott Fones <boson245 at gmail.com> wrote:
> You were exactly right about the dmesg.
>  ivtv: ==================== START INIT IVTV ====================
>  ivtv: version 0.2.0 (rc3j) loading
>  ivtv: Linux version: 2.6.12-gentoo-r8 preempt gcc-3.4
>  ivtv: In case of problems please include the debug info
>  ivtv: between the START INIT IVTV and END INIT IVTV lines when
>  ivtv: mailing the ivtv-devel mailinglist.
>  ivtv: Autodetected WinTV PVR 250 card
>  ivtv: Found an iTVC16 based chip
>  ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC3] -> GSI 18 (level, low)
> -> IRQ 217
>  ivtv: Unreasonably low latency timer, setting to 64 (was 32)
>  ivtv: XXX PCI device: 0x005e vendor: 0x10de
>  tveeprom: Hauppauge: model = 32062, rev = C199, serial# = 8115353
>  tveeprom: tuner = <unknown> (idx = 99, type = 4)
>  tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
>  tveeprom: audio_processor = MSP3445 (type = 12)
>  ivtv: i2c attach [client=tveeprom,ok]
>  ivtv: Tuner Type 4, Tuner formats 0x00001000, Radio: yes, Model 0x008d1659,
> Revision 0x00000000
>  ivtv: NTSC tuner detected
>  ivtv: Radio detected
>  ivtv: Failed to load module tuner
>  saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
>  saa7115: detecting saa7115 client on address 0x42
>  saa7115: writing init values
>  ivtv: i2c attach [client=saa7115,ok]
>  saa7115: status: (1E) 0x00, (1F) 0xc0
>  msp34xx: ivtv version
>  msp34xx: init: chip=MSP3445G-B8, has NICAM support, simple (D) mode,
> simpler (G) no-thread mode
>  msp34xx: $Id$ compiled on: Sep  2 2005 04:01:16
>  ivtv: i2c attach [client=MSP3445G-B8,ok]
>  ivtv: Encoder revision: 0x02040024
>  ivtv: Encoder Firmware may be buggy, use version 0x02040011
>  ivtv: Configuring WinTV PVR 250 card with 5 streams
>  ivtv: Create DMA stream 0 using 256 16384 byte buffers  4194304 kbytes
> total
>  ivtv: Registered v4l2 device, streamtype 0 minor 0
>  ivtv: Create DMA stream 1
>  ivtv: Registered v4l2 device, streamtype 1 minor 32
>  ivtv: Create stream 2 using 40 52224 byte buffers  2097152 kbytes total
>  ivtv: Registered v4l2 device, streamtype 2 minor 224
>  ivtv: Create DMA stream 3 using 455 4608 byte buffers  2097152 kbytes total
>  ivtv: Registered v4l2 device, streamtype 3 minor 24
>  ivtv: Create stream 4
>  ivtv: Registered v4l2 device, streamtype 4 minor 64
>  ivtv: Setting Tuner 4
>  ivtv: i2c client id: 0x02 not found!
>  ivtv: i2c client id: 0x02 not found!
>  saa7115: decoder set input (4)
>  saa7115: now setting Composite input
>  ivtv: Setting audio matrix to input 3, output 1
>  ivtv: Switching standard to NTSC.
>  ivtv: i2c client id: 0x02 not found!
>  ivtv: ivtv_enc_thread: pid = 3904, itv = 0xffffffff88464c60
>  saa7115: decoder set norm NTSC
>  saa7115: set audio: 0x01
>  ivtv: Initialized WinTV PVR 250, card #0
>  ivtv: ====================  END INIT IVTV  ====================
>  
>  I've redone the ivtv install and checked my kernel config, but can't seem
> to figure this out.  Since I need to get a little sleep, I figured I'd post
> this and see if anyone has any ideas.  Thanks for the help!
>  
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
> 
> 
>