[mythtv-users] Pvr-250 refuses channel change

Scott Fones boson245 at gmail.com
Fri Sep 2 08:12:48 UTC 2005


You were exactly right about the dmesg.
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.2.0 (rc3j) loading
ivtv: Linux version: 2.6.12-gentoo-r8 preempt gcc-3.4
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 250 card
ivtv: Found an iTVC16 based chip
ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC3] -> GSI 18 (level, low) -> 
IRQ 217
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: XXX PCI device: 0x005e vendor: 0x10de
tveeprom: Hauppauge: model = 32062, rev = C199, serial# = 8115353
tveeprom: tuner = <unknown> (idx = 99, type = 4)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = MSP3445 (type = 12)
ivtv: i2c attach [client=tveeprom,ok]
ivtv: Tuner Type 4, Tuner formats 0x00001000, Radio: yes, Model 0x008d1659, 
Revision 0x00000000
ivtv: NTSC tuner detected
ivtv: Radio detected
ivtv: Failed to load module tuner
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
saa7115: detecting saa7115 client on address 0x42
saa7115: writing init values
ivtv: i2c attach [client=saa7115,ok]
saa7115: status: (1E) 0x00, (1F) 0xc0
msp34xx: ivtv version
msp34xx: init: chip=MSP3445G-B8, has NICAM support, simple (D) mode, simpler 
(G) no-thread mode
msp34xx: $Id$ compiled on: Sep 2 2005 04:01:16
ivtv: i2c attach [client=MSP3445G-B8,ok]
ivtv: Encoder revision: 0x02040024
ivtv: Encoder Firmware may be buggy, use version 0x02040011
ivtv: Configuring WinTV PVR 250 card with 5 streams
ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 1
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Create stream 4
ivtv: Registered v4l2 device, streamtype 4 minor 64
ivtv: Setting Tuner 4
ivtv: i2c client id: 0x02 not found!
ivtv: i2c client id: 0x02 not found!
saa7115: decoder set input (4)
saa7115: now setting Composite input
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to NTSC.
ivtv: i2c client id: 0x02 not found!
ivtv: ivtv_enc_thread: pid = 3904, itv = 0xffffffff88464c60
saa7115: decoder set norm NTSC
saa7115: set audio: 0x01
ivtv: Initialized WinTV PVR 250, card #0
ivtv: ==================== END INIT IVTV ====================

I've redone the ivtv install and checked my kernel config, but can't seem to 
figure this out. Since I need to get a little sleep, I figured I'd post this 
and see if anyone has any ideas. Thanks for the help!
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://mythtv.org/pipermail/mythtv-users/attachments/20050902/ebae6639/attachment.htm


More information about the mythtv-users mailing list