[mythtv-users] black stripes with hauppauge 250

[Milan Andric]

On Mon, Oct 04, 2004 at 09:56:34PM -0700, Milan Andric wrote:
> Hello, I have been unable to make black vertical lines 
> disappear from my video using the hauppauge 250 after following
> jarod's guide.  I set this up a few weeks ago when the guide
> had just recently updated to mythtv 0.16 and FC2. 
> I tried using differnet interlacing algorithms 
> but that didn't change much.
> 
> i'm not sure where to start fixing, or peice of the puzzle is
> most likely the problem.  any advice is appreciated.
> 
> here's a picture of the WinTV PVR 250 card:
> http://www.lebox.org/node/view/592
> 
> output from cat /dev/video0 :
> http://www.lebox.org/u/milan/tmp/m.mpg
> 
> relevant lines from /etc/modules.conf:
> 
> # ivtv modules setup
> alias char-major-81 videodev
> alias char-major-81-0 ivtv
> install ivtv /sbin/modprobe msp3400 saa7115 tuner v4l1-compat; /sbin/modprobe --ignore-install ivtv
> #options ivtv ivtv_debug=1 tuner=2 cardtype=1
> options ivtv ivtv_debug=1 tuner=39 cardtype=1
> #trying
> options tuner type=39
> options msp3400 once=0 simpler=1 simple=0
> alias char-major-61 lirc_i2c
> install lirc_i2c /sbin/modprobe ivtv; /sbin/modprobe --ignore-install lirc_i2c
> 
> ivtv driver versions:
> 
> $ rpm -qa |grep ivtv
> kernel-module-ivtv-2.6.8-1.521-0.1.10-45_pre2_ck108k.rhfc2.at
> ivtv-0.1.10-45_pre2_ck108k.rhfc2.at
> perl-Video-ivtv-0.12-5.1.rhfc2.at
> ivtv-firmware-2.02.023-3.at
> 

also, here is the ivtv debug info :

ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.1.10 (0.1.10pre2-ck108k) loading
ivtv: Linux version: 2.6.8-1.521 686 REGPARM 4KSTACKS gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: User specified WinTV PVR 250 card
ivtv: Found an iTVC16 based chip
ACPI: PCI interrupt 0000:00:0b.0[A] -> GSI 5 (level, low) -> IRQ 5
ivtv: XXX PCI device: 0x0735 vendor: 0x1039
msp34xx: ivtv version
msp34xx: init: chip=MSP3448W-B3, has NICAM support, simple (D) mode, simpler (G) no-thread mode
msp34xx: $Id$ compiled on: Sep  9 2004 17:13:54
ivtv: i2c attach [client=MSP3448W-B3,ok]
tveeprom: Hauppauge: model = 32032, rev = B182, serial# = 2832464
tveeprom: tuner = LG NTSC (newer TAPC series) (idx = 82, type = 39)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = MSP3440 (type = 11)
ivtv: i2c attach [client=tveeprom[0],ok]
ivtv: Tuner Type 39, Tuner formats 0x00001000, Radio: yes, Model 0x00891612, Revision 0x00000000
ivtv: NTSC tuner detected
ivtv: Radio detected
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
tuner: type set to 39 (LG NTSC (newer TAPC series)) by insmod option
tuner: The type=<n> insmod option will go away soon.
tuner: Please use the tuner=<n> option provided by
tuner: tv aard core driver (bttv, saa7134, ...) instead.
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
saa7115: detecting saa7115 client on address 0x42
saa7115: writing init values
ivtv: i2c attach [client=saa7115[0],ok]
saa7115: status: (1E) 0x09, (1F) 0xc0
ivtv: Encoder revision: 0x02040011
ivtv: Configuring WinTV PVR 250 card with 5 streams
ivtv: Create DMA stream 0 using 16 131072 byte buffers  2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 1 using 16 131072 byte buffers  2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create stream 2 using 512 4096 byte buffers  2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 3 using 16 131072 byte buffers  2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Create stream 4
ivtv: Registered v4l2 device, streamtype 4 minor 64
ivtv: Setting Tuner 39
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to NTSC.
saa7115: decoder set norm NTSC
saa7115: set audio: 0x01
ivtv: Initialized WinTV PVR 250, card #0
ivtv: ====================  END INIT IVTV  ====================

thanks for any tips,

-- 
Milan