[mythtv-users] Mythfilldatabase, new HdHr Quatro box, and EPG
Don Brett
dlbrett at zoominternet.net
Wed Aug 7 19:37:20 UTC 2019
On 8/7/2019 1:33 PM, Klaas de Waal wrote:
> On Wed, 7 Aug 2019 at 16:16, Don Brett <dlbrett at zoominternet.net> wrote:
>> I missed the announcements when my local broadcasters decided to change
>> frequencies and required everyone to re-scan. I thought my HDHR-Connect
>> box stopped working, so I bought a new HDHR-Quatro (four tuners).
>>
>> The installation went pretty well. I deleted the existing tuners and
>> created four new ones for the Quatro box (thanks Klaas for the
>> instructions). The channel scan worked fine and all four tuners are
>> working better than expected; some of the hard to get channels are
>> working really well.
>>
>> However, the program guide is unpopulated ("Unknown(Unknown)" for all
>> the new tuner channels. I also have an Hauppauge HD-PVR for the cable
>> box and those channels are fine. I've run mythfilldatabase several
>> times; do I have a myth-setup issue, or maybe something with
>> Schedules-Direct?
>>
>> Don
>>
>> PS - After the channel scan, I checked the channel editor and all looked
>> fine. I exited and re-entered mythtv-setup and re-checked the channel
>> editor. Filtering for each of the Quatro antenna inputs, it shows all
>> the cable-tv channels mixed into the antenna channels. Example: if I
>> set the "Video Sources" filter to "All", it shows five cable TV "Video
>> On Demand" channels (HD-PVR, Ant-1. Ant-2, Ant-3. Ant-4). I assume this
>> is a display issue, but ??
>>
>> PS - I temporarily turned on EIT and it mostly filled in the guide.
>>
>> PS - I reported the frequency change to Schedules-Direct and asked if
>> any updates were needed on their end; waiting for response.
>>
> The way I understand your system you need to configure two video
> sources, one for the HD-PVR/cable and one for the Quatro/OTA.
> All four tuners of the Quatro have to be connected to the one video
> source you created for the Quatro/OTA.
> In the mythtv-setup Channel Editor, when you select "All" video
> sources, you get all channels from all video sources.
> If there are channels that are both on the HD-PVR/cable and on the
> Quattro/OTA then you see that channel twice.
> Note that on the mythfrontend Program Guide the same channel from
> different video sources is shown only once.
> If you want to use EIT/EPG then you need to do that on only one tuner
> per video source. So for the Quattro/OTA you configure EIT/EPG only
> for the first tuner.
>
> I am not familiar with Schedules-Direct but maybe it works
> automatically OK once the setup is correct.
>
> Klaas.
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://lists.mythtv.org/mailman/listinfo/mythtv-users
> http://wiki.mythtv.org/Mailing_List_etiquette
> MythTV Forums: https://forum.mythtv.org
>
Perhaps I misunderstood. The Quatro has four tuners in one box, using
one IP address, and one device ID. Do I actually have only two capture
cards (HDPVR and HDHOMERUN)? Here's what I created, what do I need to
delete?
Capture cards >
HDPVR: /dev/video0
HDHOMERUN: 10722347
HDHOMERUN: 10722347
HDHOMERUN: 10722347
HDHOMERUN: 10722347
Video Sources >
HdPvr
Ant-1
Ant-2
Ant-3
Ant-4
Input Connections >
[HDPVR: /dev/video0] (Component) -> HdPvr
[HDHOMERUN: 10722347] (MPEG2TS) -> Ant-1
[HDHOMERUN: 10722347] (MPEG2TS) -> Ant-2
[HDHOMERUN: 10722347] (MPEG2TS) -> Ant-3
[HDHOMERUN: 10722347] (MPEG2TS) -> Ant-4
Don
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
More information about the mythtv-users
mailing list