[mythtv-users] Trouble with HDHOMERUN drivers

Tue Apr 16 17:10:31 UTC 2019

You should have a hdhr config on your desktop menu. See if that can see the
hdhr. It sounds like an IP address issue. I have my hdhr ip addresses
reserved in my router.  I also had to set addressed static and I assume you
will need to do the same. See my thread on that. Last update was this
morning.

On Tue, Apr 16, 2019, 9:48 AM DryHeat122 <dryheat122 at gmail.com> wrote:

>
>
> On Tue, Apr 16, 2019 at 9:28 AM Allen Edwards <allen.p.edwards at gmail.com>
> wrote:
>
>>
>>
>>
>>
>>> On Tue, Apr 16, 2019 at 7:30 AM Allen Edwards <allen.p.edwards at gmail.com>
>>> wrote:
>>>
>>>>
>>>>
>>>> On Tue, Apr 16, 2019 at 6:48 AM DryHeat122 <dryheat122 at gmail.com>
>>>> wrote:
>>>>
>>>>> Turns out @allen was right, and I could install the input source
>>>>> without installing any drivers.  I was able to watch live TV via Myth after
>>>>> setting everything up; however, Myth won't seem to record anything off the
>>>>> HDHomerun.  I currently have a cable box connected via HDPVR to the same BE
>>>>> (the one I'm hoping to get rid of by recording OTA).  For some of the shows
>>>>> I record from broadcast networks, I went into recording rules and set the
>>>>> input source to "prefer" one of the HDHomerun tuners.  But when it comes
>>>>> time to record the show, the HDPVR is lit up and apparently doing the
>>>>> recording.
>>>>>
>>>>> Below are some lines from the time the Ellen show (recording for my
>>>>> wife) was set to start recording.  Can anyone tell from this what the
>>>>> problem might be?
>>>>>
>>>>> Apr 15 15:00:00 steve-EP45-UD3P mythbackend: mythbackend[798]: E
>>>>> Scheduler recordingprofile.cpp:162 (addSelection) SampleRate: Attempted to
>>>>> add a rate 32000 Hz, which is not in the list of allowed rates.
>>>>> Apr 15 15:00:00 steve-EP45-UD3P mythbackend: mythbackend[798]: I
>>>>> TVRecEvent tv_rec.cpp:1073 (HandleStateChange) TVRec[1]: Changing from None
>>>>> to RecordingOnly
>>>>> Apr 15 15:00:00 steve-EP45-UD3P mythbackend: mythbackend[798]: I
>>>>> TVRecEvent mythdbcon.cpp:422 (PurgeIdleConnections) New DB connection,
>>>>> total: 8
>>>>> Apr 15 15:00:00 steve-EP45-UD3P mythbackend: mythbackend[798]: I
>>>>> TVRecEvent tv_rec.cpp:3563 (TuningCheckForHWChange) TVRec[1]: HW Tuner: 1->1
>>>>> Apr 15 15:00:00 steve-EP45-UD3P mythbackend: mythbackend[798]: I
>>>>> TVRecEvent tv_rec.cpp:3685 (TuningFrequency) TVRec[1]: TuningFrequency
>>>>> Apr 15 15:00:00 steve-EP45-UD3P mythbackend: mythbackend[798]: I
>>>>> Scheduler scheduler.cpp:2819 (HandleRecordingStatusChange) Tuning
>>>>> recording: "The Ellen DeGeneres Show":"Bill Hader": channel 2012 on cardid
>>>>> 1, sourceid 1
>>>>> Apr 15 15:00:00 steve-EP45-UD3P mythbackend: mythbackend[798]: C
>>>>> CoreContext programinfo.cpp:351 (ProgramInfo) ProgramInfo(): Failed to find
>>>>> recorded entry for 0.
>>>>> Apr 15 15:00:00 steve-EP45-UD3P mythbackend: mythbackend[798]: E
>>>>> ProcessRequest programinfo.cpp:2594 (GetPlaybackURL)
>>>>> ProgramInfo(2012_20190415220000.ts): GetPlaybackURL:
>>>>> '2012_20190415220000.ts' should be local, but it can not be found.
>>>>> Apr 15 15:00:00 steve-EP45-UD3P mythbackend: mythbackend[798]: E
>>>>> ProcessRequest programinfo.cpp:2594 (GetPlaybackURL)
>>>>> ProgramInfo(2012_20190415220000.ts): GetPlaybackURL:
>>>>> '2012_20190415220000.ts' should be local, but it can not be found.
>>>>> Apr 15 15:00:03 steve-EP45-UD3P mythbackend: mythbackend[798]: I
>>>>> CoreContext scheduler.cpp:725 (UpdateRecStatus) Updating status for "The
>>>>> Ellen DeGeneres Show":"Bill Hader" on cardid 1 (Tuning => Recording)
>>>>> Apr 15 15:00:03 steve-EP45-UD3P mythbackend: mythbackend[798]: E
>>>>> TVRecEvent recordingprofile.cpp:162 (addSelection) SampleRate: Attempted to
>>>>> add a rate 32000 Hz, which is not in the list of allowed rates.
>>>>> Apr 15 15:00:03 steve-EP45-UD3P mythbackend: mythbackend[798]: I
>>>>> TVRecEvent tv_rec.cpp:4215 (TuningNewRecorder) TVRec[1]:
>>>>> rec->GetPathname():
>>>>> '/home/steve/mythvideo/recordings/2012_20190415220000.ts'
>>>>> Apr 15 15:00:03 steve-EP45-UD3P mythbackend: mythbackend[798]: I
>>>>> TVRecEvent tv_rec.cpp:4247 (TuningNewRecorder) TVRec[1]: TuningNewRecorder
>>>>> - CreateRecorder()
>>>>> Apr 15 15:00:03 steve-EP45-UD3P mythbackend: mythbackend[798]: E
>>>>> RecThread recorders/mpegrecorder.cpp:1418 (StartEncoding)
>>>>> MPEGRec[1](/dev/video0): StartEncoding: read failed, retry in 100
>>>>> msec:#012#011#011#011eno: Resource temporarily unavailable (11)
>>>>>
>>>>>
>>>>> On Mon, Apr 15, 2019 at 8:01 AM Curtis Gedak <gedakc at gmail.com> wrote:
>>>>>
>>>>>> On 2019-04-14 1:54 p.m., DryHeat122 wrote:
>>>>>> > @curtis, no except I did what the silicondust support page said.
>>>>>> Assuming
>>>>>> > I don't have @allen's experience, do I need to install all the
>>>>>> packages in
>>>>>> > your message?
>>>>>>
>>>>>>
>>>>>> If you wish the GUI and the library I think all that is needed is:
>>>>>>
>>>>>> sudo apt-get install hdhomerun-config hdhomerun-config-gui
>>>>>> libhdhomerun2
>>>>>>
>>>>>> Normally the "dev" libraries are only needed if you are compiling from
>>>>>> source code.
>>>>>>
>>>>>> 'Hope that helps.
>>>>>>
>>>>>>
>>>>>> Curtis
>>>>>
>>>>>
>>>> I do not get the sample rate error so not sure what that is about. What
>>>> I would try is to try and record multiple shows at once so that your cable
>>>> box channel is in use and Myth would need to use the HDHR to record a show.
>>>> Hopefully the show will record. I don't know why a show would not record
>>>> from a preferred input if you have selected in in the recording rule.
>>>>
>>>> Another tip is that in Mythweb, you can click on the show icon on the
>>>> left and read which input name was actually used to record the show.
>>>>
>>>> Allen
>>>>
>>>
>> On Tue, Apr 16, 2019 at 9:09 AM DryHeat122 <dryheat122 at gmail.com> wrote:
>> OK here's something.  I took your good suggestion to record a second show
>> at the same time as Ellen.  I found a channel that is available on the
>> antenna but not cable.  When I set it to single-record on the program
>> guide, it said the recorder is offline.  Yet I checked again and I could
>> watch live TV on the antenna source.  Anyone have ideas about what could
>> cause this?  Maybe the missing drivers from HDHomerun?
>>
>> Do you have all the three screens in backend setup done correctly? Do you
>> have the channels setup and the input connections?  Just must be something
>> in the setup but I can't think of what it can be.
>>
>> Allen
>>
>> PS.  They like you to bottom post for some reason so I moved your input.
>> _______________________________________________
>> mythtv-users mailing list
>> mythtv-users at mythtv.org
>> http://lists.mythtv.org/mailman/listinfo/mythtv-users
>> http://wiki.mythtv.org/Mailing_List_etiquette
>> MythTV Forums: https://forum.mythtv.org
>
>
> AFAIK I have it set up correctly.  The antenna listings are in the program
> guide.  I said before that I could see the content on "Watch TV" but I just
> checked again and I can't.  Maybe I was mistaken when I said that before.
> So something is not right and I have no idea how to troubleshoot.
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://lists.mythtv.org/mailman/listinfo/mythtv-users
> http://wiki.mythtv.org/Mailing_List_etiquette
> MythTV Forums: https://forum.mythtv.org
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.mythtv.org/pipermail/mythtv-users/attachments/20190416/0686df76/attachment.html>