[mythtv-users] ?Card?

Daryl McDonald darylangela at gmail.com
Tue Jun 18 23:44:48 UTC 2013


On Tue, Jun 18, 2013 at 7:22 PM, George Nassas <gnassas at mac.com> wrote:

> On 2013-06-18, at 6:57 PM, Daryl McDonald wrote:
>
> After a reboot, there is much more to grep:
>
>
> Apologies, I’m not saying things very well. The kworld card is going to be
> probed at slightly different times in each boot sequence. That’s normal. In
> the first log output you posted it happened at the 21 second mark but it
> seems after your reboot the card is being probed at a different time
> because there’s no relevant output during the 21st second.
>
> So, start with one of these:
>
> dmesg | grep -i -E "kworld|dvb”
>

 daryl at daryl-A780L3C:~$ dmesg | grep -i -E "kworld|dvb"
[   20.796356] saa7133[0]: subsystem: 17de:a135, board: Kworld PC150-U
[card=189,insmod option]
[   20.930930] tveeprom 2-0050: TV standards NTSC(M) ATSC/DVB Digital
(eeprom 0x88)
[   21.702705] cx23885_dvb_register() allocating 1 frontend(s)
[   21.702707] cx23885[0]: cx23885 based dvb card
[   21.734221] DVB: registering new adapter (cx23885[0])
[   21.734224] DVB: registering adapter 0 frontend 0 (Samsung S5H1409
QAM/8VSB Frontend)...
[   57.755937] Registered IR keymap rc-kworld-pc150u
[   57.756041] input: i2c IR (Kworld PC150-U) as
/devices/virtual/rc/rc0/input11
[   57.756108] rc0: i2c IR (Kworld PC150-U) as /devices/virtual/rc/rc0
[   57.756111] ir-kbd-i2c: i2c IR (Kworld PC150-U) detected at
i2c-1/1-0030/ir0 [saa7133[0]]
[   57.805166] dvb_init() allocating 1 frontend
[   60.014045] DVB: registering new adapter (saa7133[0])
[   60.014047] DVB: registering adapter 1 frontend 0 (Samsung S5H1411
QAM/8VSB Frontend)...

>
> and take note of when the saa7134 output starts happening (if it’s not
> there then do a “modprobe saa7134” as root). Then, do one of these:
>
> dmesg | grep -E ‘NN[.]’
>
> where NN is the time of the saa7134 messages. That will be the interesting
> output and hopefully it doesn’t cross a seconds boundary.
>
I went after saa 1733 NN being 20:

 daryl at daryl-A780L3C:~$ dmesg | grep -E '20[.]'
[    1.265913] powernow-k8: Found 1 AMD Athlon(tm) II X3 445 Processor (3
cpu cores) (version 2.20.00)
[   20.491928] Adding 8386556k swap on /dev/sda5.  Priority:-1 extents:1
across:8386556k
[   20.496143] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   20.537228] udevd[437]: starting version 175
[   20.713574] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00,
revision 0
[   20.714645] lp: driver loaded but no devices found
[   20.715601] sp5100_tco: SP5100 TCO WatchDog Timer Driver v0.01
[   20.716591] sp5100_tco: mmio address 0xfec000f0 already in use
[   20.717031] MCE: In-kernel MCE decoding enabled.
[   20.717444] EDAC MC: Ver: 2.1.0
[   20.720642] [drm] Initialized drm 1.1.0 20060810
[   20.721138] type=1400 audit(1371596965.012:2): apparmor="STATUS"
operation="profile_load" name="/sbin/dhclient" pid=509
comm="apparmor_parser"
[   20.721525] type=1400 audit(1371596965.012:3): apparmor="STATUS"
operation="profile_load"
name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=509
comm="apparmor_parser"
[   20.721743] type=1400 audit(1371596965.012:4): apparmor="STATUS"
operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script"
pid=509 comm="apparmor_parser"
[   20.722861] type=1400 audit(1371596965.012:5): apparmor="STATUS"
operation="profile_replace" name="/sbin/dhclient" pid=598
comm="apparmor_parser"
[   20.723246] type=1400 audit(1371596965.012:6): apparmor="STATUS"
operation="profile_replace"
name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=598
comm="apparmor_parser"
[   20.723303] microcode: CPU0: patch_level=0x010000c8
[   20.723463] type=1400 audit(1371596965.012:7): apparmor="STATUS"
operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script"
pid=598 comm="apparmor_parser"
[   20.723701] type=1400 audit(1371596965.012:8): apparmor="STATUS"
operation="profile_load" name="/usr/sbin/ntpd" pid=646
comm="apparmor_parser"
[   20.725534] type=1400 audit(1371596965.016:9): apparmor="STATUS"
operation="profile_replace" name="/usr/sbin/ntpd" pid=647
comm="apparmor_parser"
[   20.731774] AMD64 EDAC driver v3.4.0
[   20.731976] EDAC amd64: DRAM ECC disabled.
[   20.731987] EDAC amd64: ECC disabled in the BIOS or no ECC capability,
module will not load.
[   20.731987]  Either enable ECC checking or force module loading by
setting 'ecc_enable_override'.
[   20.731987]  (Note that use of the override may cause unknown side
effects.)
[   20.738335] wmi: Mapper loaded
[   20.742808] Linux video capture interface: v2.00
[   20.779213] [drm] radeon defaulting to kernel modesetting.
[   20.779217] [drm] radeon kernel modesetting enabled.
[   20.779465] [drm] initializing kernel modesetting (CEDAR 0x1002:0x68F9
0x1462:0x2127).
[   20.779486] [drm] register mmio base: 0xFE7E0000
[   20.779487] [drm] register mmio size: 131072
[   20.780185] ATOM BIOS: 113
[   20.780294] radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 -
0x000000003FFFFFFF (1024M used)
[   20.780297] radeon 0000:01:00.0: GTT: 512M 0x0000000040000000 -
0x000000005FFFFFFF
[   20.780544] [drm] Detected VRAM RAM=1024M, BAR=256M
[   20.780548] [drm] RAM width 64bits DDR
[   20.782503] parport_pc 00:07: reported by Plug and Play ACPI
[   20.782635] parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[   20.784440] [TTM] Zone  kernel: Available graphics memory: 4088982 kiB
[   20.784443] [TTM] Zone   dma32: Available graphics memory: 2097152 kiB
[   20.784445] [TTM] Initializing pool allocator
[   20.784449] [TTM] Initializing DMA pool allocator
[   20.784472] [drm] radeon: 1024M of VRAM memory ready
[   20.784473] [drm] radeon: 512M of GTT memory ready.
[   20.784490] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[   20.784491] [drm] Driver supports precise vblank timestamp query.
[   20.784529] radeon 0000:01:00.0: irq 45 for MSI/MSI-X
[   20.784539] radeon 0000:01:00.0: radeon: using MSI.
[   20.784570] [drm] radeon: irq initialized.
[   20.784574] [drm] GART: num cpu pages 131072, num gpu pages 131072
[   20.785582] [drm] Loading CEDAR Microcode
[   20.793776] ppdev: user-space parallel port driver
[   20.796128] saa7130/34: v4l2 driver version 0, 2, 17 loaded
[   20.796349] saa7133[0]: found at 0000:04:01.0, rev: 209, irq: 21,
latency: 64, mmio: 0xfebff800
[   20.796356] saa7133[0]: subsystem: 17de:a135, board: Kworld PC150-U
[card=189,insmod option]
[   20.796377] saa7133[0]: board init: gpio is 100000
[   20.803818] cx23885 driver version 0.0.3 loaded
[   20.803990] CORE cx23885[0]: subsystem: 0070:7911, board: Hauppauge
WinTV-HVR1250 [card=3,autodetected]
[   20.836190] microcode: CPU1: patch_level=0x010000c8
[   20.838411] microcode: CPU2: patch_level=0x010000c8
[   20.840037] microcode: Microcode Update Driver: v2.00 <
tigran at aivazian.fsnet.co.uk>, Peter Oruba
[   20.843959] kvm: Nested Virtualization enabled
[   20.843964] kvm: Nested Paging enabled
[   20.876775] lp0: using parport0 (interrupt-driven).
[   20.930924] tveeprom 2-0050: Hauppauge model 79571, rev D5D9, serial#
5129055
[   20.930926] tveeprom 2-0050: MAC address is 00:0d:fe:4e:43:5f
[   20.930928] tveeprom 2-0050: tuner model is Microtune MT2131 (idx 139,
type 4)
[   20.930930] tveeprom 2-0050: TV standards NTSC(M) ATSC/DVB Digital
(eeprom 0x88)
[   20.930931] tveeprom 2-0050: audio processor is CX23885 (idx 39)
[   20.930933] tveeprom 2-0050: decoder processor is CX23885 (idx 33)
[   20.930934] tveeprom 2-0050: has no radio
[   20.930935] cx23885[0]: hauppauge eeprom: model=79571
[   20.982269] saa7133[0]: i2c eeprom 00: de 17 35 a1 ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.982276] saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.982281] saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.982285] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.982290] saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.982294] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.982299] saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.982304] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.982308] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.982313] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.982317] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.982322] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.982326] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.982331] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.982335] saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.982340] saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[   20.983551] cx25840 4-0044: cx23885 A/V decoder found @ 0x88 (cx23885[0])
[   20.988801] [drm] PCIE GART of 512M enabled (table at
0x0000000000040000).
[   20.988922] radeon 0000:01:00.0: WB enabled
[   20.988925] radeon 0000:01:00.0: fence driver on ring 0 use gpu addr
0x0000000040000c00 and cpu addr 0xffff88020cb2ac00
daryl at daryl-A780L3C:~$

yes?

>
> One more thing: if/when we do get this card recognized you’re going to end
> up with two adapters in /dev/dvb and no consistency as to the numbering.
> Sometimes the kworld will be adapter1 and sometimes adapter0. Myth, on the
> other hand, is configured to expect your cable digital tuner to be adapter0
> and if the kworld suddenly appears there you’ll lose recordings. It’s easy
> to handle this but until you get to that point you can “rm
> /etc/modprobe.d/pc150u.conf” when you’re done experimenting and put it back
> the next time you work on getting the card recognized.
>
> - George
>
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://www.mythtv.org/mailman/listinfo/mythtv-users
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.mythtv.org/pipermail/mythtv-users/attachments/20130618/8a1e3a57/attachment-0001.html>


More information about the mythtv-users mailing list