[mythtv-users] hauppauge hvr 1600 with hvr 1250
Claude Gélinas
claude at phyto.qc.ca
Fri Dec 28 02:24:13 UTC 2012
I've reinstalled a new mythtv system where from fedora17 clean install
there are three hauppauge cards pvr 500, hvr 1600 and a new hvr 1250
the first two are detected correctly but the 1250 give the following
message in dmesg
dmesg | grep cx18
[ 11.109374] cx18: Start initialization, version 1.5.1
[ 11.109389] cx18-0: Initializing card 0
[ 11.109390] cx18-0: Autodetected Hauppauge card
[ 11.113686] cx18-0: cx23418 revision 01010000 (B)
[ 11.325150] cx18-0: Autodetected Hauppauge HVR-1600
[ 11.325151] cx18-0: Simultaneous Digital and Analog TV capture supported
[ 11.417097] cs5345 4-004c: chip found @ 0x98 (cx18 i2c driver #0-0)
[ 11.598720] cx18-0: Registered device video0 for encoder MPEG (64 x 32.00 kB)
[ 11.598723] DVB: registering new adapter (cx18)
[ 11.654504] cx18-0: DVB Frontend registered
[ 11.654505] cx18-0: Registered DVB adapter0 for TS (32 x 32.00 kB)
[ 11.654531] cx18-0: Registered device video32 for encoder YUV (20 x 101.25 kB)
[ 11.654555] cx18-0: Registered device vbi0 for encoder VBI (20 x 51984 bytes)
[ 11.654575] cx18-0: Registered device video24 for encoder PCM audio (256 x 4.00 kB)
[ 11.654576] cx18-0: Initialized card: Hauppauge HVR-1600
[ 11.654595] cx18: End initialization
[ 12.248227] cx18-alsa: module loading...
[ 12.497884] cx18-0: loaded v4l-cx23418-cpu.fw firmware (158332 bytes)
[ 12.870295] cx18-0: loaded v4l-cx23418-apu.fw firmware V00120000 (141200 bytes)
[ 12.876457] cx18-0: FW version: 0.0.74.0 (Release 2007/03/12)
[ 13.832870] cx18-0 843: loaded v4l-cx23418-dig.fw firmware (16382 bytes)
[ 13.857519] cx18-0 843: verified load of v4l-cx23418-dig.fw firmware (16382 bytes)
[74074.800682] cx18 0000:08:01.0: vpd r/w failed. This is likely a
firmware bug on this device. Contact the card vendor for a firmware
update.
dmesg | grep cx23885
[ 12.254619] cx23885 driver version 0.0.3 loaded
[ 12.254793] CORE cx23885[0]: subsystem: 0070:2259, board: Hauppauge WinTV-HVR1255 [card=20,insmod option]
[ 12.402905] cx23885[0]: hauppauge eeprom: model=22111
[ 12.404575] cx25840 10-0044: cx23888 A/V decoder found @ 0x88 (cx23885[0])
[ 41.733895] cx25840 10-0044: loaded v4l-cx23885-avcore-01.fw firmware (16382 bytes)
[ 41.767185] cx23885[0]: registered device video3 [v4l2]
[ 41.767381] cx23885[0]: registered device vbi3
[ 41.767699] cx23885[0]: registered ALSA audio device
[ 41.839989] cx23885_dvb_register() allocating 1 frontend(s)
[ 41.839991] cx23885[0]: cx23885 based dvb card
[ 42.007286] cx23885[0]: frontend initialization failed
[ 42.007290] cx23885_dvb_register() dvb_register failed err = -22
[ 42.007291] cx23885_dev_setup() Failed to register dvb on VID_C
[ 42.007294] cx23885_dev_checkrevision() Hardware revision = 0xd0
[ 42.007298] cx23885[0]/0: found at 0000:07:00.0, rev: 4, irq: 16, latency: 0, mmio: 0xf3e00000
why the frontend initialization failed for the 1250 ??
can I have these two card in the same computer or should I keep just one
any idea
--
Claude Gélinas agr.
Phyto Ressources Inc
More information about the mythtv-users
mailing list