[mythtv-users] Pinnacle PCTV HD Card

Sat Jun 21 07:19:39 UTC 2008

On Fri, 2008-06-20 at 18:33 -0700, J. Addington wrote:
> Which driver in the package did you load?

I was following the instructions on here:

http://www.mythtv.org/wiki/index.php/Pinnacle_PCTV_HD_Card_(800i)

> 
> Also, which branch did you download for the drivers and what is your kernel version?

My kernel is a stock mythbuntu 2.6.24-19-generic, and I downloaded the
drivers from here:

http://linuxtv.org/hg/v4l-dvb

I think I downloaded the bzip version, which has unpacked into a
directory v4l-dvb-afa24b594522. I have the firmware file
dvb-fe-xc5000-1.1.fw, although I've just realized it's not in the
appropriate directory (it's in /lib/firmware/2.6.24-18-generic/ not 19)
I'll put it in there and recompile the drivers.

Thanks, Tom

> 
> 
> 
> 
> 
> ----- Original Message ----
> From: Tom Haddon <tom at haddons.net>
> To: Discussion about mythtv <mythtv-users at mythtv.org>
> Sent: Friday, June 20, 2008 6:47:16 PM
> Subject: Re: [mythtv-users] Pinnacle PCTV HD Card
> 
> On Fri, 2008-06-20 at 16:24 -0700, J. Addington wrote:
> > It's probably not the same problem but I recently installed this card and was having a problem with the v4l-dvb drivers.  There are several branches where you can download a kernel module source and compile but I just ended up upgrading my entire kernel to the latest stable version and the included 4dl-dvb drivers then worked fine.
> 
> I think you might be onto the right track here. I recompiled the v4l-dvb
> modules and now I'm able to run:
> 
> scan 
> /usr/share/doc/dvb-utils/examples/scan/atsc/us-ATSC-center-frequencies-8VSB > channels.conf 
> 
> Previously I was getting errors telling me the
> device /dev/dvb/adapter0/frontend0 didn't exist, so I think I was
> looking at a kernel/kernel module issue.
> 
> However, I get the following when I run the scan command:
> 
> mthaddon at sentinel:~$
> scan /usr/share/doc/dvb-utils/examples/scan/atsc/us-ATSC-center-frequencies-8VSB > channels.conf
> scanning /usr/share/doc/dvb-utils/examples/scan/atsc/us-ATSC-center-frequencies-8VSB
> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
> >>> tune to: 57028615:8VSB
> WARNING: >>> tuning failed!!!
> >>> tune to: 57028615:8VSB (tuning failed)
> WARNING: >>> tuning failed!!!
> >>> tune to: 63028615:8VSB
> WARNING: >>> tuning failed!!!
> >>> tune to: 63028615:8VSB (tuning failed)
> WARNING: >>> tuning failed!!!
> >>> tune to: 69028615:8VSB
> WARNING: >>> tuning failed!!!
> [...]
> ERROR: initial tuning failed
> dumping lists (0 services)
> Done.
> 
> 
> All the channels seem to fail this way, and I'm left with an empty
> channels.conf. Doesn't seem good :(
> 
> Thanks, Tom
> 
> > 
> > 
> > ----- Original Message ----
> > From: Tom Haddon <tom at haddons.net>
> > To: mythtv-users at mythtv.org
> > Sent: Friday, June 20, 2008 4:41:54 PM
> > Subject: [mythtv-users] Pinnacle PCTV HD Card
> > 
> > Hi Folks,
> > 
> > I've just bought a Pinnacle PCTV HD Card as per
> > http://www.bestbuy.com/site/olspage.jsp?skuId=8512424&type=product&id=1186005934822 and I'm trying to configure it to worth with my hardy Mythbuntu install.
> > 
> > I've been following the instructions on
> > http://mythtv.org/wiki/index.php/Pinnacle_PCTV_HD_Card_(800i) and have
> > extracted the firmware, and compiled the v4l-dvb drivers per that page.
> > I'm then able to see the device as an option in mythtvsetup. I've
> > configured it as an MPEG-2 encoder card, and in the "Probed Info"
> > section it's showing "Pinnacle PCTV HD800i [cx8800]". I've then setup
> > Schedules Direct as a Video Source, and under "Input Connections" I've
> > defined "[MPEG: /dev/video0] (Television) -> Schedules Direct". I've
> > then performed the "Scan for Channels" and have got a bunch of channels
> > showing up (I'm just using rabbit ears, don't have cable or satellite),
> > but when I go to "Watch TV" on the mythfrontend I get a blank screen for
> > a few seconds and then I'm returned to the main menu. I see the
> > following in the frontend log:
> > 
> > 2008-06-07 09:28:57.828 TV: Attempting to change from None to
> > WatchingLiveTV
> > 2008-06-07 09:28:57.829 Using protocol version 40
> > 2008-06-07 09:29:03.102 GetEntryAt(-1) failed.
> > 2008-06-07 09:29:03.103 EntryToProgram(0 at Wed Dec 31 16:00:00 1969)
> > failed to get pginfo
> > 2008-06-07 09:29:03.103 TV Error: LiveTV not successfully started
> > 2008-06-07 09:29:03.138 TV Error: LiveTV not successfully started
> > 2008-06-07 09:29:03.234 TV: Deleting TV Chain in destructor
> > 2008-06-07 09:29:03.238 DPMS Deactivated
> > 2008-06-07 09:29:03.238 DPMS Reactivated.
> > 
> > Also, after a recent update to linux-restricted-modules, whenever I run
> > the mythtv-setup script and try to go to any of the pages (General,
> > Capture Cards, Video Source, etc.) I get a message saying "If this is
> > the master backend server, please run mythfilldatabase to populate the
> > database with channel information". The only option is "OK" at which
> > point mythtv-setup exits and I'm asked to run that mythfilldatabase. If
> > I do, it runs fine, but still I get the same message when I re-run
> > mythtv-setup. So now I can't see my current config, or change it in any
> > way...
> > 
> > Any help appreciated.
> > 
> > Thanks, Tom
> > 
> > _______________________________________________
> > mythtv-users mailing list
> > mythtv-users at mythtv.org
> > http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
> > 
> > 
> > 
> >      
> > _______________________________________________
> > mythtv-users mailing list
> > mythtv-users at mythtv.org
> > http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
> 
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
> 
> 
> 
>       
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users