[mythtv-users] Lost Sound on PVR-350 After Upgrade to IVTV 0.4.1
Matt Price
matt.price at utoronto.ca
Tue Mar 6 01:55:16 UTC 2007
kirk, i found the post below in my maibox. this problem you describe sounds
like the one i'm having now -- i had mythtv running fine under ubuntu
breeazy for over a year, then tried to upgrade, failedsomehow, rebooted into
my old root system and suddenly no sound! i was wondering whether you had
solved this and if so, whether you still remember how!
as i say i htink this is the same issue -- sound OUTPUT works fine, and my
old recordings still play fine through pvr-350's tv-out; but sound input
through the capture card no longer works, there simply isn't any audio being
processed. any idea how to fix it? i'm at a loss, all these modules are
sorta greek to me.
thanks,
matt
On Sat, Dec 31, 2005 at 03:45:42PM -0800, Kirk Bocek wrote:
> I upgraded my MythTV system from ivtv 0.4.0 and kernel 2.6.13.2 to ivtv
> 0.4.1 and kernel 2.6.14.4 and now I get no sound on my PVR-350 from
> either live tv or recorded programs.
>
> Sound system is working - Xine playing DVDs and MythMusic output sound fine.
>
> I've reset the settings in alsamixer/amixer: master and PCM to 75%
> unmuted, CD (which the PVR-350 is plugged into) at 75%, muted and set as
> the capture source. Internal cabling has not changed from my previously
> working ivtv 0.4.0 setup.
>
> The correct msp3400 is being loaded -- I compiled ivtv from source and
> executed the recommended mv commands.
>
> Any suggestions?
>
> My init messages are below.
>
> Thanks,
> Kirk
>
>
>
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.4.1 (tagged release) loading
> ivtv: Linux version: 2.6.14.4-wcpvr01 SMP gcc-3.4
> ivtv: In case of problems please include the debug info between
> ivtv: the START INIT IVTV and END INIT IVTV lines, along with
> ivtv: any module options, when mailing the ivtv-users mailinglist.
> ivtv0: Autodetected WinTV PVR 350 card (cx23415 based)
> ACPI: PCI Interrupt 0000:01:02.0[A] -> GSI 17 (level, low) -> IRQ 185
> ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
> ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
> tveeprom 0-0050: The eeprom says no radio is present, but the tuner type
> tveeprom 0-0050: indicates otherwise. I will assume that radio is present.
> tveeprom 0-0050: Hauppauge model 48132, rev K268, serial# 2985761
> tveeprom 0-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47)
> tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
> tveeprom 0-0050: audio processor is MSP4448 (idx 27)
> tveeprom 0-0050: decoder processor is SAA7115 (idx 19)
> tveeprom 0-0050: has radio, has IR remote
> tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
> ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
> saa7115 0-0021: ivtv driver
> saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21]
> saa7127 0-0044: ivtv driver
> saa7127 0-0044: saa7129 found @ 0x88 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44]
> msp3400 0-0040: ivtv driver
> msp3400 0-0040: chip=MSP4448G-A2 +nicam +simple +simpler +radio mode=simpler
> msp3400 0-0040: msp34xxg daemon started
> ivtv0: i2c attach to card #0 ok [client=MSP4448G-A2, addr=40]
> tda9887 0-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
> ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
> ivtv0: Encoder revision: 0x02050032
> ivtv0: Decoder revision: 0x02020023
> ivtv0: Allocate DMA encoder MPEG stream: 256 x 32768 buffers (8192KB total)
> ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
> ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
> ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
> total)
> ivtv0: Create encoder radio stream
> ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
> ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
> ivtv0: Create decoder VOUT stream
> ivtv0: Allocate DMA decoder YUV stream: 48 x 43200 buffers (2048KB total)
> ivtv0: loaded v4l-cx2341x-init-mpeg.bin firmware (155648 bytes)
> tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
> tuner: switching to v4l2
> tuner: tv freq set to 67.25
> tuner: tv 0x07 0x10 0x8e 0x01
> ivtv0: Initialized WinTV PVR 350, card #0
> ivtv: ==================== END INIT IVTV ====================
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
More information about the mythtv-users
mailing list