[mythtv-users] Tuning problems with HD5000
Michael Carland
mcarland at bitsgonewild.net
Tue Aug 7 16:45:54 UTC 2007
I am having problems with an HD5000 that used to work. I needed a
kernel upgrade to fix some network instability, and I think that is
when the problem began. I don't watch much DTV, so I'm not certain
the problem started with the new kernel.
My symptom is that the card is recognized properly, but it doesn't
seem to want to tune. Most of the time scan says it fails tuning, so
of course azap can't get a lock. At one point, I don't know how, but
the tuner tuned to the local PBS station. scan then thought it could
tune, but it was always on the PBS station, spitting out a list of
the PBS channels for each frequency it thought it was tuning to. When
I would change channels in Myth, it would think it was on various
channels, but always displayed one of the PBS channels.
Has anyone had this problem and found a fix, or is anyone having
success with an HD5000 on a newer kernel (I'm at 2.6.22.1 on amd64)?
I don't think this is a myth specific issue, but I'm hoping there are
a few HD5000 users on this list.
Thanks.
stern:/# lspci -v -s 4:06.0
04:06.0 Network controller: Techsan Electronics Co Ltd B2C2 FlexCopII
DVB chip / Technisat SkyStar2 DVB card (rev 02)
Subsystem: Techsan Electronics Co Ltd B2C2 FlexCopII DVB
chip / Technisat SkyStar2 DVB card
Flags: bus master, slow devsel, latency 64, IRQ 19
Memory at feaf0000 (32-bit, non-prefetchable) [size=64K]
I/O ports at bc00 [size=32]
stern:/# dmesg
...
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip
loaded successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 2
ACPI: PCI Interrupt 0000:04:06.0[A] -> Link [LNKA] -> GSI 19 (level,
low) -> IRQ19
DVB: registering new adapter (FlexCop Digital TV device).
b2c2-flexcop: MAC address = 00:d0:d7:0e:6b:f0
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
mt352_read_register: readreg error (reg=127, ret==-121)
b2c2-flexcop: i2c master_xfer failed
nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)
Unknown/Unsupported NXT chip: 00 00 00 00 00
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: found the lgdt3303 at i2c address: 0x59
DVB: registering frontend 0 (LG Electronics LGDT3303 VSB/QAM
Frontend)...
b2c2-flexcop: initialization of 'Air2PC/AirStar 2 ATSC 3rd generation
(HD5000)' at the 'PCI' bus controlled by a 'FlexCopIIb' complete
...
mythtv at stern:~$ scan us-MSP
scanning us-MSP
using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
>>> tune to: 599000000:8VSB
WARNING: >>> tuning failed!!!
>>> tune to: 599000000:8VSB (tuning failed)
WARNING: >>> tuning failed!!!
>>> tune to: 593000000:8VSB
WARNING: >>> tuning failed!!!
>>> tune to: 593000000:8VSB (tuning failed)
WARNING: >>> tuning failed!!!
More information about the mythtv-users
mailing list