[mythtv-users] saa7134 card

[Michael Lynch]

FC4
P4 2.8 GHz
1GB RAM
200GB
Compro VideoMate TV Gold+ (Phillips saa713x based capture card)
MythTV .19 from ATRPMs

I have a Compro VideoMate TV Gold+ card that is Phillips saa713x based
that I all of the sudden can't seem to get working.  I have previously
had the card working in Myth but I built a new box and now it's not.

I am able to get full audio/video with xawtv.  When I try to watch TV
from within Myth all I get is a 'scrambled' picture.  This happens on
any channel that I try to tune to from within Myth.

# lspci -v

02:0a.0 Multimedia controller: Philips Semiconductors SAA7133 Video
Broadcast Decoder (rev 10)
        Subsystem: Compro Technology, Inc. Compro VideoMate TV Gold+
        Flags: bus master, medium devsel, latency 32, IRQ 185
        Memory at feafe800 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [40] Power Management version 2

# dmesg |grep saa

saa7130/34: v4l2 driver version 0.2.14 loaded
saa7133[0]: found at 0000:02:0a.0, rev: 16, irq: 185, latency: 32,
mmio: 0xfeafe800
saa7133[0]: subsystem: 185b:c100, board: Compro VideoMate TV
[card=19,autodetected]
saa7133[0]: board init: gpio is cc0000
saa7133[0]: i2c eeprom 00: 5b 18 00 c1 ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff 00 ff 00 05 33 11 cb
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tuner 1-0060: chip found @ 0xc0 (saa7133[0])
tuner 1-0068: chip found @ 0xd0 (saa7133[0])
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0

<at this point I set options for the saa7134 module to force card and
tuner, remove the module, run depmod -a, modprobe saa7134>

# dmesg |grep saa
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 185
saa7133[0]: found at 0000:02:0a.0, rev: 16, irq: 185, latency: 32,
mmio: 0xfeafe800
saa7133[0]: subsystem: 185b:c100, board: Compro VideoMate TV
[card=19,insmod option]
saa7133[0]: board init: gpio is cc0000
tuner 1-0060: All bytes are equal. It is not a TEA5767
tuner 1-0060: chip found @ 0xc0 (saa7133[0])
tuner 1-0060: type set to 17 (Philips NTSC_M (MK2))
tuner 1-0068: chip found @ 0xd0 (saa7133[0])
saa7133[0]: i2c eeprom 00: 5b 18 00 c1 ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff 00 ff 00 05 33 11 cb
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0


As you can see I have tried letting the card be auto-detected and used
module options via modprobe.conf.  Any suggestions would be
appreciated.


-- 
...For example I long ago decided I will never go to meetings again
because I think face to face meetings are the biggest waste of time
you can ever have. I think most people who work at offices must share
my opinion on meetings. Nothing ever gets done. When things get done,
you usually have someone come into your office to talk about it. But a
lot of the time the real work gets done by people sitting, especially
in programming, alone in front of their computers doing what they do
best.

-Linus Torvalds