[mythtv-users] Composite since upgrade to 0.19

James Pifer jep at obrien-pifer.com
Fri Jul 14 16:10:28 UTC 2006


I recently upgraded to 0.19 and most things are working well. One
problem I have is my composite input, which I had configured and working
with 0.18. After the upgrade I had to delete all my card settings and
redo them. 

I can't figure out what input to use. I have a PVR350 and a PVR250. I'm
trying to use the composite on the 250. Here's my ivtv output:
ivtv:  ==================== START INIT IVTV ====================
ivtv:  version 0.6.2 (development snapshot compiled on Mon May 22 01:17:37 2006) loading
ivtv:  Linux version: 2.6.16-1.2122_FC5 686 REGPARM 4KSTACKS gcc-4.1
ivtv:  In case of problems please include the debug info between
ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
ivtv:  any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-350 card (cx23415 based)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
tveeprom 1-0050: Hauppauge model 48132, rev J333, serial# 6547160
tveeprom 1-0050: tuner model is Temic 4039FR5 (idx 33, type 21)
tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 1-0050: audio processor is MSP4448 (idx 27)
tveeprom 1-0050: decoder processor is SAA7115 (idx 19)
tveeprom 1-0050: has radio, has IR remote
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
saa7115 1-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
saa7127 1-0044: saa7127 found @ 0x88 (ivtv i2c driver #0)
msp3400 1-0040: MSP4448G-A2 found @ 0x80 (ivtv i2c driver #0)
msp3400 1-0040: MSP4448G-A2 supports radio, mode is autodetect and autoselect
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02040024
ivtv0: Decoder revision: 0x02020023
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
ivtv0: Create decoder VOUT stream
ivtv0: Allocate DMA decoder YUV stream: 24 x 43200 buffers (1024KB total)
ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes)
tuner 1-0061: type set to 21 (Temic NTSC (4039 FR5))
spurious 8259A interrupt: IRQ7.
ivtv0: Initialized Hauppauge WinTV PVR-350, card #0
ACPI: PCI Interrupt 0000:00:02.7[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
intel8x0_measure_ac97_clock: measured 55576 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:03.3[D] -> Link [LNKH] -> GSI 5 (level, low) -> IRQ 5
ehci_hcd 0000:00:03.3: EHCI Host Controller
PCI: cache line size of 64 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:03.3: irq 5, io mem 0xcfffb000
ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.0: irq 11, io mem 0xcfff8000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:03.1[B] -> Link [LNKF] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.1: irq 5, io mem 0xcfff9000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:03.2[C] -> Link [LNKG] -> GSI 11 (level, low) -> IRQ 11
ohci_hcd 0000:00:03.2: OHCI Host Controller
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:03.2: irq 11, io mem 0xcfffa000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ivtv:  ======================  NEXT CARD  ======================
ivtv1: Autodetected Hauppauge WinTV PVR-250 card (cx23416 based)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #1)
saa7115 2-0021: saa7115 found @ 0x42 (ivtv i2c driver #1)
msp3400 2-0040: MSP4448G-A2 found @ 0x80 (ivtv i2c driver #1)
msp3400 2-0040: MSP4448G-A2 supports radio, mode is autodetect and autoselect
tveeprom 2-0050: Hauppauge model 32032, rev B310, serial# 7044326
tveeprom 2-0050: tuner model is Philips FI1236 MK2 (idx 10, type 2)
tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 2-0050: audio processor is MSP4448 (idx 27)
tveeprom 2-0050: decoder processor is SAA7115 (idx 19)
tveeprom 2-0050: has no radio, has IR remote
ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv1: Encoder revision: 0x02040024
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
tuner 2-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles))
ivtv1: Initialized Hauppauge WinTV PVR-250, card #1
ivtv:  ====================  END INIT IVTV  ====================

So in mythtv I have /dev/video0 and /dev/video1. I assume my PVR250 is
video1 based on the ivtv setup?

I've created a channel called composite. How do I know what input to
assign it to? I've tried a couple and it has not worked. 

I have:
S-Video 1
Composite 1
S-Video 2
Composite 2
Composite 3

Any help is appreciated.

Thanks,
James




More information about the mythtv-users mailing list