[mythtv-users] KnoppMyth R5A26 and Hauppauge Nova-T

[Dave Ansell]

What is output from lsmod?

Broblem I had with Nova-T was the cx88_blackbird module loaded instead of 
cx88_dvb.

Check you have cx99_dvb loaded corectly.


----- Original Message ----- 
From: "Myth TV" <mythtv at fsmail.net>
To: <mythtv-users at mythtv.org>
Sent: Wednesday, January 04, 2006 11:00 PM
Subject: [mythtv-users] KnoppMyth R5A26 and Hauppauge Nova-T


>I have purchased the Hauppauge Nova-t card to be used in my mythtv system 
>because I have read that it is well supported and works best for DVB in the 
>UK.
>
> However after installing the KnoppMyth R5A26 it does not recognise the 
> model and does not set up the card properly.
>
> The extract from dmesg is :-
>
> Linux video capture interface: v1.00
> cx2388x dvb driver version 0.0.5 loaded
> cx88[0]: subsystem: 0070:9002, board: Hauppauge Nova-T DVB-T 
> [card=18,autodetected]
> TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
> tveeprom(cx88xx internal): Huh, no eeprom present (err=-121)?
> cx88[0]: warning: unknown hauppauge model #0
> cx88[0]: error: unknown hauppauge tuner 0x00
> cx88[0]: registered IR remote control
> PCI: Enabling device 0000:00:0f.2 (0014 -> 0016)
> ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
> PCI: setting IRQ 10 as level-triggered
> ACPI: PCI Interrupt 0000:00:0f.2[A] -> Link [LNKC] -> GSI 10 (level, 
> low) -> IRQ 10
> cx88[0]/2: found at 0000:00:0f.2, rev: 5, irq: 10, latency: 32, mmio: 
> 0xeb000000
> cx88[0]/2: cx2388x based dvb card
> DVB: registering new adapter (cx88[0]).
> DVB: registering frontend 0 (Hauppauge Nova-T DVB-T)...
> ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 9 (level, 
> low) -> IRQ 9
> 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
> 0000:00:0b.0: 3Com PCI 3c905C Tornado at 0xa400. Vers LK1.1.19
> cx2388x v4l2 driver version 0.0.5 loaded
> PCI: Enabling device 0000:00:0f.0 (0014 -> 0016)
> ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKC] -> GSI 10 (level, 
> low) -> IRQ 10
> cx88[0]/0: found at 0000:00:0f.0, rev: 5, irq: 10, latency: 32, mmio: 
> 0xec000000
> cx88[0]/0: registered device video0 [v4l2]
> cx88[0]/0: registered device vbi0
>
> however when I come to configure the card in mythtv-setup and select DVB 
> as the card it does not recognise it.
>
> what am I doing wrong ?
>
> and how can I fix it ?
>
> any help will be much appreciated.
>
> Tad
>
>


--------------------------------------------------------------------------------


_______________________________________________
mythtv-users mailing list
mythtv-users at mythtv.org
http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users