[mythtv-users] Lost Sound on PVR-350 After Upgrade to IVTV 0.4.1
Kirk Bocek
t004 at kbocek.com
Sun Jan 1 02:16:05 EST 2006
Thanks, Joshua, I'll give that a try. I had quite a few messages with
Hans Verkuil on the ivtv-users list about this. He didn't mention any
similar problems. I think I will try rolling back the driver though.
I'll post my results.
Kirk
Joshua Frank wrote:
> I had the same problem. I eventually just reinstalled ivtv 0.4.0. But if
> you want to play with some thing interesting try this command
>
> ivtvctl -d /dev/video0 -q 1
>
> This tells your ivtv card to use audio channel 1 instead of 0. I heard
> that the was a problem with the drivers no selecting the correct
> channel. Could be worth a try.
>
> On 12/31/05, *Kirk Bocek* <t004 at kbocek.com <mailto:t004 at kbocek.com>> wrote:
>
> I upgraded my MythTV system from ivtv 0.4.0 and kernel 2.6.13.2
> <http://2.6.13.2> to ivtv
> 0.4.1 and kernel 2.6.14.4 <http://2.6.14.4> and now I get no sound
> on my PVR-350 from
> either live tv or recorded programs.
>
> Sound system is working - Xine playing DVDs and MythMusic output
> sound fine.
>
> I've reset the settings in alsamixer/amixer: master and PCM to 75%
> unmuted, CD (which the PVR-350 is plugged into) at 75%, muted and
> set as
> the capture source. Internal cabling has not changed from my previously
> working ivtv 0.4.0 setup.
>
> The correct msp3400 is being loaded -- I compiled ivtv from source and
> executed the recommended mv commands.
>
> Any suggestions?
>
> My init messages are below.
>
> Thanks,
> Kirk
>
>
>
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.4.1 (tagged release) loading
> ivtv: Linux version: 2.6.14.4-wcpvr01 SMP gcc-3.4
> ivtv: In case of problems please include the debug info between
> ivtv: the START INIT IVTV and END INIT IVTV lines, along with
> ivtv: any module options, when mailing the ivtv-users mailinglist.
> ivtv0: Autodetected WinTV PVR 350 card (cx23415 based)
> ACPI: PCI Interrupt 0000:01:02.0[A] -> GSI 17 (level, low) -> IRQ 185
> ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
> ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
> tveeprom 0-0050: The eeprom says no radio is present, but the tuner type
> tveeprom 0-0050: indicates otherwise. I will assume that radio is
> present.
> tveeprom 0-0050: Hauppauge model 48132, rev K268, serial# 2985761
> tveeprom 0-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47)
> tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
> tveeprom 0-0050: audio processor is MSP4448 (idx 27)
> tveeprom 0-0050: decoder processor is SAA7115 (idx 19)
> tveeprom 0-0050: has radio, has IR remote
> tuner (ivtv): chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
> ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
> saa7115 0-0021: ivtv driver
> saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21]
> saa7127 0-0044: ivtv driver
> saa7127 0-0044: saa7129 found @ 0x88 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=saa7127, addr=44]
> msp3400 0-0040: ivtv driver
> msp3400 0-0040: chip=MSP4448G-A2 +nicam +simple +simpler +radio
> mode=simpler
> msp3400 0-0040: msp34xxg daemon started
> ivtv0: i2c attach to card #0 ok [client=MSP4448G-A2, addr=40]
> tda9887 0-0043: (ivtv) chip found @ 0x86 (ivtv i2c driver #0)
> ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]
> ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
> ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
> ivtv0: Encoder revision: 0x02050032
> ivtv0: Decoder revision: 0x02020023
> ivtv0: Allocate DMA encoder MPEG stream: 256 x 32768 buffers (8192KB
> total)
> ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB
> total)
> ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB
> total)
> ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB
> total)
> ivtv0: Create encoder radio stream
> ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB
> total)
> ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB
> total)
> ivtv0: Create decoder VOUT stream
> ivtv0: Allocate DMA decoder YUV stream: 48 x 43200 buffers (2048KB
> total)
> ivtv0: loaded v4l-cx2341x-init-mpeg.bin firmware (155648 bytes)
> tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
> tuner: switching to v4l2
> tuner: tv freq set to 67.25
> tuner: tv 0x07 0x10 0x8e 0x01
> ivtv0: Initialized WinTV PVR 350, card #0
> ivtv: ==================== END INIT IVTV ====================
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org <mailto:mythtv-users at mythtv.org>
> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
> <http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users>
>
>
>
>
> --
> Joshua Frank
> frankjoshua at gmail.com <mailto:frankjoshua at gmail.com>
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
More information about the mythtv-users
mailing list