[mythtv-users] No Live TV PVR-350

[Robert Seaton]

I have went through the backend setup process, and think I have
configured it correctly, but being new to this MythTV stuff I cannot say
I have configured it correctly for sure. Here is the iVTV portin of the
dmesg output. Again thank you for your help.
 
 
dmesg:
 
ivtv: ==================== START INIT IVTV ====================

ivtv: version 0.8.1 (tagged release) loading

ivtv: Linux version: 2.6.18-1.2849.fc6 SMP mod_unload 686 REGPARM
4KSTACKS gcc-4.1

ivtv: In case of problems please include the debug info between

ivtv: the START INIT IVTV and END INIT IVTV lines, along with

ivtv: any module options, when mailing the ivtv-users mailinglist.

ivtv0: Autodetected Hauppauge card (cx23415 based)

PCI: Enabling device 0000:00:0d.0 (0014 -> 0016)

ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 16 (level, low) -> IRQ 177

ivtv0: Unreasonably low latency timer, setting to 64 (was 32)

ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)

ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes) tveeprom
0-0050: Hauppauge model 48132, rev J333, serial# 6547046 tveeprom
0-0050: tuner model is Temic 4039FR5 (idx 33, type 21) tveeprom 0-0050:
TV standards NTSC(M) (eeprom 0x08) tveeprom 0-0050: audio processor is
MSP4448 (idx 27) tveeprom 0-0050: decoder processor is SAA7115 (idx 19)
tveeprom 0-0050: has radio, has IR remote

ivtv0: Autodetected Hauppauge WinTV PVR-350 tuner 0-0061: chip found @
0xc2 (ivtv i2c driver #0)

saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)

saa7127 0-0044: saa7127 found @ 0x88 (ivtv i2c driver #0) msp3400
0-0040: MSP4448G-A2 found @ 0x80 (ivtv i2c driver #0) msp3400 0-0040:
MSP4448G-A2 supports radio, mode is autodetect and autoselect

ivtv0: Encoder revision: 0x02050032

ivtv0: Decoder revision: 0x02020023

ivtv0: Registered device video0 for encoder MPEG

ivtv0: Registered device video32 for encoder YUV

ivtv0: Registered device vbi0 for encoder VBI

ivtv0: Registered device video24 for encoder PCM audio

ivtv0: Registered device radio0 for encoder radio

ivtv0: Registered device video16 for decoder MPEG

ivtv0: Registered device vbi8 for decoder VBI

ivtv0: Registered device vbi16 for decoder VOUT

ivtv0: Registered device video48 for decoder YUV

ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes) tuner 0-0061:
type set to 21 (Temic NTSC (4039 FR5))

ivtv0: Initialized Hauppauge WinTV PVR-350, card #0

PCI: Enabling device 0000:00:05.0 (0084 -> 0085)

ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 17 (level, low) -> IRQ 193

ivtv: ==================== END INIT IVTV ====================


________________________________

From: mythtv-users-bounces at mythtv.org
[mailto:mythtv-users-bounces at mythtv.org] On Behalf Of koen mythtv
Sent: Friday, December 01, 2006 10:21 AM
To: Discussion about mythtv
Subject: Re: [mythtv-users] No Live TV PVR-350




On 12/1/06, Robert Seaton <bobs at itproscorp.com> wrote: 


	One step away from everything working. Everything seems to be
working
	except when I run Mythfrontend, and attempt to use the Live TV
option 
	the screen goes black for about three minutes, and then goes
back to the
	menu page. Can anyone point me in the right direction? Many
Thanks in
	advance.
	
	
	I have included the mythtfrontend out, and an excerpt from the
mythtvlog 
	at the bottom.

 
<SNIP>
 
did you configure the 350 in mythbackend? 
Select appr. inputs? 
 
what does dmesg say after inserting the ivtv modules?
 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://mythtv.org/pipermail/mythtv-users/attachments/20061201/f8b73a2b/attachment.htm