[mythtv-users] Blank LiveTV, Can't View Video Playback, Can Record

[cyko]

Hello list.

I am trying to get my PVR-350 working with MythTV-0.17.  I'll get
straight to the point.

I can cat /dev/v4l/video0 > test.mpg and replay it back using mplayer
with both video and audio.  I'm using basic cable (from the wall jack to
the PVR input) and would like playback directly onto a connected monitor
so I assume my input connection should be Tuner 0.

That said, every other input connection is set to none.  Below is my
ivtv output:

ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.2.0 (rc3g) loading
ivtv: Linux version: 2.6.9 preempt K7 4KSTACKS gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 350 card
ivtv: Found an iTVC15 based chip
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 18
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: VIA PCI device: 0x3189 vendor: 0x1106
ivtv: i2c attach [client=unset,ok]
ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-2/2-0018/ir0 [ivtv i2c
driver #0]
msp34xx: ivtv version
msp34xx: init: chip=MSP3448W-A2, has NICAM support, simple (D) mode,
simpler (G) no-thread mode
msp34xx: $Id$ compiled on: Mar  6 2005 01:31:00
ivtv: i2c attach [client=MSP3448W-A2,ok]
tda9885/6/7: chip found @ 0x86
ivtv: i2c attach [client=tda9887,ok]
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
tveeprom: Hauppauge: model = 48132, rev = K168, serial# = 2836801
tveeprom: tuner = LG TAPE H001F MK3 (idx = 68, type = 47)
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
tveeprom: audio_processor = MSP3440 (type = 11)
ivtv: i2c attach [client=tveeprom[0],ok]
ivtv: Tuner Type 47, Tuner formats 0x00001000, Radio: yes, Model
0x00ad1598, Revision 0x00000001
ivtv: NTSC tuner detected
ivtv: Radio detected
saa7115: starting probe for adapter ISA main adapter (0x0)
saa7115: starting probe for adapter SMBus Via Pro adapter at 5000 (0x0)
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
saa7115: detecting saa7115 client on address 0x42
saa7115: writing init values
ivtv: i2c attach [client=saa7115[0],ok]
saa7115: status: (1E) 0x00, (1F) 0xc0
saa7127: video encoder driver version V 0.3 loaded
saa7127: Selecting NTSC video Standard
saa7127: Selecting S-Video+Composite
saa7127: Turn WSS off
saa7127: Widescreen Mode 4:3 Full Format
saa7127: Selecting Normal Encoder Input
saa7127: Enable Video Output
ivtv: i2c attach [client=saa7127[0],ok]
ivtv: Encoder revision: 0x02040011
ivtv: Decoder revision: 0x02020023
ivtv: Configuring WinTV PVR 350 card with 9 streams
ivtv: Create DMA stream 0 using 256 16384 byte buffers  4194304 kbytes total
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 1
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create stream 2 using 40 52224 byte buffers  2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 3 using 455 4608 byte buffers  2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Create stream 4
ivtv: Registered v4l2 device, streamtype 4 minor 64
ivtv: Create DMA stream 5 using 16 65536 byte buffers  1048576 kbytes total
ivtv: Registered v4l2 device, streamtype 5 minor 16
ivtv: Create stream 6 using 1024 2048 byte buffers  262144 kbytes total
ivtv: Registered v4l2 device, streamtype 6 minor 228
ivtv: Create stream 7
ivtv: Registered v4l2 device, streamtype 7 minor 232
ivtv: Create DMA stream 8
ivtv: Registered v4l2 device, streamtype 8 minor 48
ivtv: Setting Tuner 47
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to NTSC.
ivtv: ivtv_enc_thread: pid = 5313, itv = 0xe0ba8c20
ivtv: ivtv_dec_thread: pid = 5314, itv = 0xe0ba8c20
saa7115: decoder set norm NTSC
saa7115: set audio: 0x01
saa7127: Setting Encoder Video Standard
saa7127: Set NTSC Video Mode
saa7127: Selecting NTSC video Standard
ivtv: Initialized WinTV PVR 350, card #0
ivtv: ====================  END INIT IVTV  ====================

So it appears as though ivtv is being loaded properly.  Once I select
"Watch TV", the monitor goes blank until I hit 'ESC'.  The
mythbacked.log shows a normal stream, displays I'm using Tuner0 along
with the channel I am currently on and the name of the show currently
playing.  I can then switch channels just fine according to the logs (I
would be tail -f'ing it on another term).  I can schedule recordings
though.  They will not play back through MythTV.  They will, however,
play back just fine using kmplayer.

Any ideas would be appreciated as to how to resolve this.  Thanks a lot.

Regards,
Patrick