[mythtv-users] PVR 350 and MythVideo

Fri Jun 17 18:31:00 UTC 2005

John Harvey wrote:

>Can you mail me the section from the messages file
>about updating registers and adjusting width/height.
>Should be at the end of the file after you run
>mplayer.
>Also the output of mplayer would be useful.
>
>Thanks
>
>John
>  
>
sigh.. Well, since that last mail, something broke. After rebooting just 
now, I'm back to a non moving green and purple screen :(

The only things I was changing were mplayer settings, and they have all 
been changed back again. So I have no idea what's changed..

As for the logs, they are all attached

thanks

Dunc
-------------- next part --------------
Jun 17 19:18:33 Gobbla kernel: ivtv: ==================== START INIT IVTV ====================
Jun 17 19:18:33 Gobbla kernel: ivtv: version 0.3.6 (n) loading
Jun 17 19:18:33 Gobbla kernel: ivtv: Linux version: 2.6.11-1.27_FC3 686 REGPARM 4KSTACKS gcc-3.4
Jun 17 19:18:33 Gobbla kernel: ivtv: In case of problems please include the debug info
Jun 17 19:18:33 Gobbla kernel: ivtv: between the START INIT IVTV and END INIT IVTV lines when
Jun 17 19:18:33 Gobbla kernel: ivtv: mailing the ivtv-devel mailinglist.
Jun 17 19:18:33 Gobbla kernel: ivtv: Autodetected WinTV PVR 350 card
Jun 17 19:18:33 Gobbla kernel: ivtv: Found an iTVC15 based chip
Jun 17 19:18:33 Gobbla kernel: ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
Jun 17 19:18:33 Gobbla kernel: PCI: setting IRQ 10 as level-triggered
Jun 17 19:18:33 Gobbla kernel: ACPI: PCI interrupt 0000:00:09.0[A] -> GSI 10 (level, low) -> IRQ 10
Jun 17 19:18:33 Gobbla kernel: ivtv: Unreasonably low latency timer, setting to 64 (was 32)
Jun 17 19:18:33 Gobbla kernel: ivtv: VIA PCI device: 0x3099 vendor: 0x1106
Jun 17 19:18:33 Gobbla kernel: tveeprom: Hauppauge: model = 48139, rev = K257, serial# = 2962861
Jun 17 19:18:33 Gobbla kernel: tveeprom: tuner = Philips FM1216 ME MK3 (idx = 57, type = 38)
Jun 17 19:18:33 Gobbla kernel: tveeprom: tuner fmt = PAL(B/G) PAL(I) SECAM(L/L) PAL(D/K) (eeprom = 0x74, v4l2 = 0x00400e17)
Jun 17 19:18:33 Gobbla kernel: tveeprom: audio_processor = CS5331 (type = 9)
Jun 17 19:18:33 Gobbla kernel: ivtv: i2c attach [client=tveeprom[50],ok]
Jun 17 19:18:33 Gobbla kernel: ivtv: Tuner Type 38, Tuner formats 0x00400e17, Radio: yes, Model 0x00ad2557, Revision 0x00000001
Jun 17 19:18:33 Gobbla kernel: ivtv: Radio detected
Jun 17 19:18:33 Gobbla kernel: tuner: Ignoring new-style parameters in presence of obsolete ones
Jun 17 19:18:33 Gobbla kernel: tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
Jun 17 19:18:33 Gobbla kernel: ivtv: i2c attach [client=(tuner unset),ok]
Jun 17 19:18:33 Gobbla kernel: saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
Jun 17 19:18:33 Gobbla kernel: saa7115: detecting saa7115 client on address 0x42
Jun 17 19:18:33 Gobbla kernel: saa7115: writing init values
Jun 17 19:18:33 Gobbla kernel: ivtv: i2c attach [client=saa7115[50],ok]
Jun 17 19:18:33 Gobbla kernel: saa7115: status: (1E) 0x00, (1F) 0xc0
Jun 17 19:18:33 Gobbla kernel: saa7127: Ignoring new-style parameters in presence of obsolete ones
Jun 17 19:18:33 Gobbla kernel: saa7127: video encoder driver version V 0.3 loaded
Jun 17 19:18:33 Gobbla kernel: saa7127: detecting saa7127 client on address 0x88
Jun 17 19:18:33 Gobbla kernel: saa7127: Selecting NTSC video Standard
Jun 17 19:18:33 Gobbla kernel: saa7127: Selecting S-Video+Composite
Jun 17 19:18:33 Gobbla kernel: saa7127: Turn WSS off
Jun 17 19:18:33 Gobbla kernel: saa7127: Widescreen Mode 4:3 Full Format
Jun 17 19:18:33 Gobbla kernel: saa7127: Selecting Normal Encoder Input
Jun 17 19:18:33 Gobbla kernel: saa7127: Enable Video Output
Jun 17 19:18:33 Gobbla kernel: ivtv: i2c attach [client=saa7127[50],ok]
Jun 17 19:18:33 Gobbla rpcidmapd: rpc.idmapd startup succeeded
Jun 17 19:18:33 Gobbla kernel: msp34xx: ivtv version
Jun 17 19:18:33 Gobbla kernel: msp34xx: init: chip=MSP3418W-B3, has NICAM support, simple (D) mode, simpler (G) no-thread mode
Jun 17 19:18:33 Gobbla kernel: msp34xx: $Id$ compiled on: Jun 17 2005 16:21:07
Jun 17 19:18:33 Gobbla kernel: ivtv: i2c attach [client=MSP3418W-B3,ok]
Jun 17 19:18:33 Gobbla kernel: tda9885/6/7: chip found @ 0x86
Jun 17 19:18:33 Gobbla kernel: ivtv: i2c attach [client=tda9887,ok]
Jun 17 19:18:33 Gobbla kernel: ivtv: Encoder revision: 0x02040024
Jun 17 19:18:33 Gobbla kernel: ivtv: Encoder Firmware may be buggy, use version 0x02040011
Jun 17 19:18:33 Gobbla kernel: ivtv: Decoder revision: 0x02020023
Jun 17 19:18:33 Gobbla kernel: ivtv: Configuring WinTV PVR 350 card with 10 streams
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 0 minor 0
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 0 using 64 32768 byte buffers  0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 1 minor 32
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 1 using 161 12960 byte buffers  0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 2 minor 224
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 2 using 165 12635 byte buffers  0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 3 minor 24
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 3 using 455 4608 byte buffers  0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 4 minor 64
Jun 17 19:18:33 Gobbla kernel: ivtv: Create stream 4 
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 5 minor 16
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 5 using 16 65536 byte buffers  0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 6 minor 228
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 6 using 1024 2048 byte buffers  0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 7 minor 232
Jun 17 19:18:33 Gobbla kernel: ivtv: Create stream 7 
Jun 17 19:18:33 Gobbla kernel: ivtv: Registered v4l2 device, streamtype 8 minor 48
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 8 using 20 51840 byte buffers  0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Create DMA stream 9 using 32 65536 byte buffers  0 kbytes total
Jun 17 19:18:33 Gobbla kernel: ivtv: Setting Tuner 38
Jun 17 19:18:33 Gobbla kernel: tuner: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3)) by ivtv i2c driver #0
Jun 17 19:18:33 Gobbla kernel: saa7115: decoder set norm PAL
Jun 17 19:18:33 Gobbla kernel: saa7115: set audio: 0x01
Jun 17 19:18:33 Gobbla kernel: saa7115: decoder set input (4)
Jun 17 19:18:33 Gobbla kernel: saa7115: now setting Composite input
Jun 17 19:18:33 Gobbla kernel: ivtv: Setting audio matrix to input 3, output 1
Jun 17 19:18:33 Gobbla kernel: ivtv: Switching standard to PAL.
Jun 17 19:18:33 Gobbla kernel: ivtv: ivtv_enc_thread: pid = 2025, itv = 0xe0e18720
Jun 17 19:18:33 Gobbla kernel: ivtv: ivtv_enc_vbi_thread: pid = 2026, itv = 0xe0e18720
Jun 17 19:18:33 Gobbla kernel: ivtv: ivtv_dec_thread: pid = 2027, itv = 0xe0e18720
Jun 17 19:18:33 Gobbla kernel: ivtv: ivtv_dec_vbi_thread: pid = 2028, itv = 0xe0e18720
Jun 17 19:18:33 Gobbla kernel: saa7115: decoder set norm PAL
Jun 17 19:18:33 Gobbla kernel: saa7115: set audio: 0x01
Jun 17 19:18:33 Gobbla kernel: saa7127: Setting Encoder Video Standard
Jun 17 19:18:33 Gobbla kernel: saa7127: Set PAL Video Mode
Jun 17 19:18:33 Gobbla kernel: saa7127: Selecting PAL video Standard
Jun 17 19:18:33 Gobbla kernel: ivtv: Initialized WinTV PVR 350, card #0
Jun 17 19:18:33 Gobbla kernel: ivtv: ====================  END INIT IVTV  ====================

Jun 17 19:20:37 Gobbla kernel: ivtv: Tried to open YUV output device but need to send data to mpeg decoder before it can be used
Jun 17 19:20:38 Gobbla kernel: ivtv: Allocate DMA stream 8 using 20 51840 byte buffers  1048576 kbytes total
Jun 17 19:20:38 Gobbla kernel: ivtv-osd: Need to adjust width to src_w 512 dst_w 720 scaled_w 512
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2834 02d002d0->02d00200 0x2838 02d002d0->02d00200
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x283c 00080000->0005b05c 0x2844 00080000->0005b05c
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2854 00200000->0016c190 
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x285c 00100000->000b60b8 0x2864 00100000->000b60b8
Jun 17 19:20:38 Gobbla kernel: ivtv-osd: Need to adjust heighth to src_h 288 dst_h 432 scaled_h 384
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2930 001aaaab->00155500 0x2938 001aaaab->00155500
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2928 00035555->0002aaa0 0x292c 00035a69->0002afb4
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2920 0006aaab->00055540 0x2924 0006afbf->00055a54
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2918 024001e0->02400180 0x291c 024000f0->024000c0
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2940 000d5555->000aaa80 0x2948 000d5555->000aaa80
Jun 17 19:20:38 Gobbla kernel: ivtv: Update reg 0x2960 00ef01df->00bf017f 

MPlayer 1.0pre7-3.4.3 (C) 2000-2005 MPlayer Team
CPU: Advanced Micro Devices Athlon MP/XP Thoroughbred (Family: 6, 
Stepping: 1)
Detected cache-line size is 64 bytes
CPUflags:  MMX: 1 MMX2: 1 3DNow: 1 3DNow2: 1 SSE: 1 SSE2: 0

Linux RTC init error in ioctl (rtc_irqp_set 1024): Permission denied
Try adding "echo 1024 > /proc/sys/dev/rtc/max-user-freq" to your system 
startupscripts.
Setting up LIRC support...
Playing Scratch (Hip-hop documentary).avi.
AVI file format detected.
VIDEO:  [DIV3]  512x288  24bpp  25.000 fps  966.7 kbps (118.0 kbyte/s)
Clip info:
 Software: Nandub v1.0rc2
==========================================================================
Opening audio decoder: [mp3lib] MPEG layer-2, layer-3
AUDIO: 44100 Hz, 2 ch, s16le, 128.0 kbit/9.07% (ratio: 16000->176400)
Selected audio codec: [mp3] afm:mp3lib (mp3lib MPEG layer-2, layer-3)
==========================================================================
vo: X11 running at 720x576 with depth 24 and 32 bpp (":0.0" => local 
display)
==========================================================================
Opening video decoder: [ffmpeg] FFmpeg's libavcodec codec family
Selected video codec: [ffdivx] vfm:ffmpeg (FFmpeg DivX ;-) (MS MPEG-4 
v3))
==========================================================================
Checking audio filter chain for 44100Hz/2ch/s16le -> 
44100Hz/2ch/s16le...
AF_pre: 44100Hz/2ch/s16le
alsa-init: 1 soundcard found, using: default
alsa: 44100 Hz/2 channels/4 bpf/60208 bytes buffer/Signed 16 bit Little 
Endian
AO: [alsa] 44100Hz 2ch s16le (2 bps)
Building audio filter chain for 44100Hz/2ch/s16le -> 
44100Hz/2ch/s16le...
Starting playback...
VDec: vo config request - 512 x 288 (preferred csp: Planar YV12)
VDec: using Planar YV12 as output csp (no 0)
Movie-Aspect is undefined - no prescaling applied.
VO: [xv] 512x288 => 512x288 Planar YV12  [fs] [zoom]
alsa-uninit: pcm closed-0.012 ct: -0.006 199/199  8%  0%  0.6% 2 0

Exiting... (Quit)