[mythtv-users] PVR500MCE tuner #1, ivtv: i2c client addr: 0x44 not found for command

[of my own]

fixed modprobe.conf.. same problem.. it's weird that it detected  it
with the typo in the first place..

On 23 Jul 2005 13:31:33 -0700, Jim Reith <reith at racores.com> wrote:
> >downloaded the correct firmware and fixed the module options, still
> >the same problem.. anymore idea? Thanks again.
> >
> >alias char-major-81 videodev
> >alias char-major-81-0 ivtv
> >alias char-major-81-1 ivtv
> >options cx25480 i2c_enable=1,1
> >options saa7127 i2c_enable=-1,-1
> 
> HA! I see it... You have a typo in your options (if the above is
> correct) cx25480 != cx25840
> 
> subtle...
> 
> >
> >ivtv: ==================== START INIT IVTV ====================
> >ivtv: version 0.3.7 (a) loading
> >ivtv: Linux version: 2.6.11-1.35_FC3 686 REGPARM 4KSTACKS gcc-3.4
> >ivtv: In case of problems please include the debug info
> >ivtv: between the START INIT IVTV and END INIT IVTV lines when
> >ivtv: mailing the ivtv-devel mailinglist.
> >ivtv: Autodetected WinTV PVR 150 card
> >ivtv: Found an iTVC16 based chip
> >ACPI: PCI interrupt 0000:03:08.0[A] -> GSI 11 (level, low) -> IRQ 11
> >ivtv: XXX PCI device: 0x1a30 vendor: 0x8086
> >tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926
> >tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57)
> >tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
> >tveeprom: audio_processor = MSP3410D (type = 5)
> >ivtv: i2c attach [client=tveeprom[50],ok]
> >tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
> >ivtv: i2c attach [client=(tuner unset),ok]
> >cx25840: starting probe on adapter ivtv i2c driver #0 (0x10005)
> >cx25840: detecting cx25840 client on address 0x88
> >cx25840: cx25843-23 found. Initializing...
> >cx25840: requesting /lib/modules/HcwMakoA.ROM
> >cx25840: firmware loaded
> >ivtv: i2c attach [client=cx25840[50],ok]
> >ivtv: i2c attach [client=wm8775[50],ok]
> >ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model
> >0x00914652, Revision 0x00000001
> >ivtv: NTSC tuner detected
> >ivtv: Radio detected
> >ivtv: Encoder revision: 0x02040011
> >ivtv: Configuring WinTV PVR 150 card with 5 streams
> >ivtv: Registered v4l2 device for encoder MPEG minor 0
> >ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
> >ivtv: Registered v4l2 device for encoder YUV minor 32
> >ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
> >ivtv: Registered v4l2 device for encoder VBI minor 224
> >ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total)
> >ivtv: Registered v4l2 device for encoder PCM audio minor 24
> >ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
> >ivtv: Registered v4l2 device for encoder radio minor 64
> >ivtv: Create encoder radio stream
> >ivtv: Setting Tuner 57
> >tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #0
> >cx25840: decoder set norm NTSC
> >cx25840: decoder set input (6)
> >cx25840: now setting Tuner input
> >cx25840: set audio input (0)
> >ivtv: Switching standard to NTSC.
> >cx25840: decoder set norm NTSC
> >ivtv: Initialized WinTV PVR 150, card #0
> >ivtv: Autodetected WinTV PVR 150 card
> >ivtv: Found an iTVC16 based chip
> >ACPI: PCI interrupt 0000:03:09.0[A] -> GSI 10 (level, low) -> IRQ 10
> >ivtv: XXX PCI device: 0x1a30 vendor: 0x8086
> >tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926
> >tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57)
> >tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)
> >tveeprom: audio_processor = MSP3410D (type = 5)
> >ivtv: i2c attach [client=tveeprom[50],ok]
> >tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1
> >ivtv: i2c attach [client=(tuner unset),ok]
> >cx25840: starting probe on adapter ivtv i2c driver #1 (0x10005)
> >ivtv: i2c attach [client=wm8775[50],ok]
> >ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model
> >0x00914652, Revision 0x00000001
> >ivtv: Radio detected
> >ivtv: ivtv_enc_thread: pid = 11202, itv = 0xe2230d20
> >ivtv: ivtv_enc_vbi_thread: pid = 11203, itv = 0xe2230d20
> >ivtv: Encoder revision: 0x02040011
> >ivtv: Configuring WinTV PVR 150 card with 5 streams
> >ivtv: Registered v4l2 device for encoder MPEG minor 1
> >ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total)
> >ivtv: Registered v4l2 device for encoder YUV minor 33
> >ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total)
> >ivtv: Registered v4l2 device for encoder VBI minor 225
> >ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total)
> >ivtv: Registered v4l2 device for encoder PCM audio minor 25
> >ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total)
> >ivtv: Registered v4l2 device for encoder radio minor 65
> >ivtv: Create encoder radio stream
> >ivtv: Setting Tuner 57
> >tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1
> >ivtv: i2c client addr: 0x44 not found for command 0x40046403!
> >ivtv: i2c client addr: 0x44 not found for command 0x40046404!
> >ivtv: i2c client addr: 0x44 not found for command 0x4004646e!
> >ivtv: Switching standard to NTSC.
> >ivtv: i2c client addr: 0x44 not found for command 0x40046403!
> >ivtv: Initialized WinTV PVR 150, card #1
> >ivtv: ====================  END INIT IVTV  ====================
> >ivtv: ivtv_enc_thread: pid = 11315, itv = 0xe22542f4
> >ivtv: ivtv_enc_vbi_thread: pid = 11316, itv = 0xe22542f4
> >
> >>  ivtv: Encoder revision: 0x02050032
> >>  ivtv: Encoder Firmware may be buggy, use version 0x02040011
> >>
> >>  Go here and get the correct firmware
> >>  http://ivtv.writeme.ch/tiki-index.php?page=FirmwareVersions
> >>
> >>  Then try again. I don't have a PVR 500 so not sure it will work, but it
> >>  can't hurt to try.
> >>
> >>
> >_______________________________________________
> >mythtv-users mailing list
> >mythtv-users at mythtv.org
> >http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
> 
> 
> 


-- 
who, what, where, when?