[mythtv-users] PVR-350 not loading X
JJ Vaas
jjvaas at gmail.com
Sun Nov 7 06:17:27 UTC 2004
Hello all,
I am experiencing some problems getting x to start on my 350. I keep getting a:
Fatal server error:
AddScreen/ScreenInit failed for driver 0
Any help would be greatly appreciated.
I am following Wilson's mythtv howto.
controller info:
00:0b.0 Multimedia video controller: Internext Compression Inc iTVC15
MPEG-2 Encoder (rev 01)
Subsystem: Hauppauge computer works Inc. WinTV PVR-350
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at e4000000 (32-bit, prefetchable)
Capabilities: [44] Power Management version 2
bin/dmesg |grep ivtv
ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.2.0 (0.2.0-55_rc2j.rhfc2.at) loading
ivtv: Linux version: 2.6.8-1.521 686 REGPARM 4KSTACKS gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 350 card
ivtv: Found an iTVC15 based chip
ivtv: Unreasonably low latency timer, setting to 64 (was 32)
ivtv: VIA PCI device: 0x3189 vendor: 0x1106
ivtv: i2c attach [client=tveeprom[0],ok]
ivtv: Tuner Type 47, Tuner formats 0x00001000, Radio: yes, Model
0x00ad1598, Revision 0x00000001
ivtv: NTSC tuner detected
ivtv: Radio detected
tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
ivtv: i2c attach [client=saa7115[0],ok]
ivtv: i2c attach [client=saa7127[0],ok]
ivtv: i2c attach [client=MSP3448W-A2,ok]
ivtv: Encoder revision: 0x02040024
ivtv: Encoder Firmware is buggy, use version 0x02040011
ivtv: Decoder revision: 0x02020023
ivtv: Configuring WinTV PVR 350 card with 9 streams
ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total
ivtv: Registered v4l2 device, streamtype 0 minor 0
ivtv: Create DMA stream 1 using 64 16384 byte buffers 1048576 kbytes total
ivtv: Registered v4l2 device, streamtype 1 minor 32
ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 2 minor 224
ivtv: Create DMA stream 3 using 128 16384 byte buffers 2097152 kbytes total
ivtv: Registered v4l2 device, streamtype 3 minor 24
ivtv: Create stream 4
ivtv: Registered v4l2 device, streamtype 4 minor 64
ivtv: Create DMA stream 5 using 16 65536 byte buffers 1048576 kbytes total
ivtv: Registered v4l2 device, streamtype 5 minor 16
ivtv: Create stream 6 using 1024 2048 byte buffers 262144 kbytes total
ivtv: Registered v4l2 device, streamtype 6 minor 228
ivtv: Create stream 7
ivtv: Registered v4l2 device, streamtype 7 minor 232
ivtv: Create DMA stream 8 using 16 65536 byte buffers 1048576 kbytes total
ivtv: Registered v4l2 device, streamtype 8 minor 48
ivtv: ivtv_enc_thread: pid = 3198, itv = 0x22e18b20
ivtv: Setting Tuner 47
ivtv: ivtv_dec_thread: pid = 3199, itv = 0x22e18b20
tuner: type set to 47 (LG NTSC (TAPE series)) by ivtv i2c driver #0
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to NTSC.
ivtv: Initialized WinTV PVR 350, card #0
ivtv: ==================== END INIT IVTV ====================
ivtv-osd: Framebuffer module loaded (attached to ivtv card id 0)
ivtv-osd: Framebuffer is at decoder-relative address 0x00510000 and
has 1704960 bytes.
ivtv-osd: screen coords: [0 0] -> [720 480]
ivtv-osd: original global alpha = 208
ivtv-osd: current OSD state = 39
ivtv-osd: new global alpha = 208 (1 255 0)
ivtv-osd: framebuffer at 0xe5510000, mapped to 0x2518c000, size 1350k
ivtv-osd: mode is 720x480x32, linelength=2880
ivtv-osd: fb0: iTVC15 TV out frame buffer device
cat /var/log/messages |grep "iTVC15 TV out"
Nov 6 23:29:22 mythtv kernel: ivtv-osd: fb0: iTVC15 TV out frame buffer device
modprobe.conf:
alias eth0 via-rhine
alias snd-card-0 snd-via82xx
install snd-via82xx /sbin/modprobe --ignore-install snd-via82xx &&
/usr/sbin/alsactl restore >/dev/null 2>&1 || :
remove snd-via82xx { /usr/sbin/alsactl store >/dev/null 2>&1 || : ; };
/sbin/modprobe -r --ignore-remove snd-via82xx
alias usb-controller ehci-hcd
alias usb-controller1 uhci-hcd
# nvidia kernel module
alias char-major-195 nvidia-1_0-6111
# ivtv modules setup
alias char-major-81 videodev
alias char-major-81-0 ivtv
install ivtv /sbin/modprobe --ignore-install ivtv; /sbin/modprobe ivtv-fb
old xorg.conf:
# XFree86 4 configuration created by pyxf86config
Section "ServerLayout"
Identifier "Default Layout"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
# RgbPath is the location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
# Multiple FontPath entries are allowed (they are concatenated together)
# By default, Red Hat 6.0 and later now use a font server independent of
# the X server to render fonts.
RgbPath "/usr/X11R6/lib/X11/rgb"
ModulePath "/usr/X11R6/lib/modules/extensions/nvidia"
ModulePath "/usr/X11R6/lib/modules/extensions"
ModulePath "/usr/X11R6/lib/modules"
FontPath "unix/:7100"
EndSection
Section "Module"
Load "dbe"
Load "extmod"
Load "fbdevhw"
Load "glx"
Load "record"
Load "freetype"
Load "type1"
EndSection
Section "InputDevice"
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"
# To disable the XKEYBOARD extension, uncomment XkbDisable.
# Option "XkbDisable"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"
# Or if you just want both to be control, use:
# Option "XkbOptions" "ctrl:nocaps"
#
Identifier "Keyboard0"
Driver "kbd"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "IMPS/2"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "yes"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "MAG 986PF"
DisplaySize 370 270
HorizSync 30.0 - 86.0
VertRefresh 50.0 - 160.0
Option "dpms"
EndSection
Section "Device"
Identifier "Videocard0"
Driver "nvidia"
VendorName "Videocard vendor"
BoardName "RIVA TNT2"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Videocard0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1024x768" "800x600" "640x480"
EndSubSection
EndSection
Section "DRI"
Group 0
Mode 0666
EndSection
new xorg.conf:
# XFree86 4 configuration created by pyxf86config
Section "ServerLayout"
Identifier "Default Layout"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
# RgbPath is the location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
# Multiple FontPath entries are allowed (they are concatenated together)
# By default, Red Hat 6.0 and later now use a font server independent of
# the X server to render fonts.
RgbPath "/usr/X11R6/lib/X11/rgb"
ModulePath "/usr/X11R6/lib/modules/extensions/nvidia"
ModulePath "/usr/X11R6/lib/modules/extensions"
ModulePath "/usr/X11R6/lib/modules"
FontPath "unix/:7100"
EndSection
Section "Module"
Load "dbe"
Load "extmod"
Load "fbdevhw"
Load "glx"
Load "record"
Load "freetype"
Load "type1"
EndSection
Section "InputDevice"
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Option "Xleds" "1 2 3"
# To disable the XKEYBOARD extension, uncomment XkbDisable.
# Option "XkbDisable"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# Option "XkbModel" "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# Option "XkbModel" "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# Option "XkbLayout" "de"
# or:
# Option "XkbLayout" "de"
# Option "XkbVariant" "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# Option "XkbOptions" "ctrl:swapcaps"
# Or if you just want both to be control, use:
# Option "XkbOptions" "ctrl:nocaps"
#
Identifier "Keyboard0"
Driver "kbd"
Option "XkbModel" "pc105"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "IMPS/2"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5"
Option "Emulate3Buttons" "yes"
EndSection
Section "Monitor"
Identifier "NTSC Monitor"
HorizSync 30-68
VertRefresh 50-120
Mode "720x480"
# D: 34.563 MHz, H: 37.244 kHz, V: 73.897 Hz
DotClock 34.564
HTimings 720 752 840 928
VTimings 480 484 488 504
Flags "-HSync" "-VSync"
EndMode
EndSection
Section "Device"
Identifier "Hauppauge PVR 350 iTVC15 Framebuffer"
Driver "ivtvdev"
#Driver "fbdev"
### change fb0 to whatever your card grabbed
Option "fbdev" "/dev/fb0"
### change the BusID to whatever is reported by lspci, specify
it as hex.
BusID "0:0x0b:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Hauppauge PVR 350 iTVC15 Framebuffer"
Monitor "NTSC Monitor"
DefaultDepth 24
DefaultFbbpp 32
Subsection "Display"
Depth 24
FbBpp 32
Modes "720x480"
EndSubsection
EndSection
Section "DRI"
Group 0
Mode 0666
EndSection
if you need anything else I will get it for you.
Thanks in advance!
JJ
More information about the mythtv-users
mailing list