[mythtv-users] Re: Still no sound

[Jo Pettitt]

OK, spent most of last night trying to get this nailed but failed 
miserably! This is what happens. After speaking with a few people on the 
ivtv development irc channel I have installed Gentoo dev-sources 
2.6.8-rc3. I have made sure that there isn't a msp3400 module in 
/lib/modules.

Then I installed ivtv 0.1.10-ck-106g.

My /etc/modules.d/ivtv file looks like this:

alias char-major-81 videodev
alias char-major-81-0 ivtv

What happens is that the picture is fine and still no audio. After 
running dmesg I see that msp3400 throws a fault like it is the wrong 
version (see below).

My question is this. Why does the fault persist even though I have the 
correct version installed in the correct place? Is there something else 
that conflicts with it? After many searches I haven't found anything 
remotely similar that hasn't been fixed!

ivtv: ==================== START INIT IVTV ====================
ivtv: version 0.1.10 (0.1.10pre2-ck106g) loading
ivtv: Linux version: 2.6.8-gentoo-r3 SMP preempt PENTIUM4 REGPARM gcc-3.3
ivtv: In case of problems please include the debug info
ivtv: between the START INIT IVTV and END INIT IVTV lines when
ivtv: mailing the ivtv-devel mailinglist.
ivtv: Autodetected WinTV PVR 350 card
ivtv: Found an iTVC15 based chip
ACPI: PCI interrupt 0000:02:0c.0[A] -> GSI 10 (level, low) -> IRQ 10
ivtv: XXX PCI device: 0x2530 vendor: 0x8086
msp34xx: init: chip=MSP3418W-A2 +nicam +simple +radio
msp3410: daemon started
ivtv: i2c attach [client=MSP3418W-A2,ok]
msp3400: error while reading chip version
ivtv: i2c attach [client=unset,ok]
ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-0/0-0018/ir0 [ivtv i2c 
driver #0]tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0
ivtv: i2c attach [client=(tuner unset),ok]
tveeprom: Hauppauge: model = 48135, rev = J324, serial# = 7015279
tveeprom: tuner = Philips FM1246 (idx = 24, type = 1)
tveeprom: tuner fmt = PAL(I) (eeprom = 0x10, v4l2 = 0x00000010)
tveeprom: audio_processor = CS5331 (type = 9)
ivtv: i2c attach [client=tveeprom[0],ok]
ivtv: Tuner Type 1, Tuner formats 0x00000010, Radio: yes, Model 
0x00a93494, Revision 0x00000001
ivtv: PAL tuner detected
ivtv: Radio detected
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)
saa7115: detecting saa7115 client on address 0x42
saa7115: writing init values
ivtv: i2c attach [client=saa7115[0],ok]
saa7115: status: (1E) 0x08, (1F) 0xc0
saa7127: video encoder driver version V 0.3 loaded
saa7127: Selecting NTSC video Standard
saa7127: Selecting S-Video+Composite
saa7127: Turn WSS off
saa7127: Widescreen Mode 4:3 Full Format
saa7127: Selecting Normal Encoder Input
saa7127: Enable Video Output
ivtv: i2c attach [client=saa7127[0],ok]
kobject_register failed for i2c msp3400 driver (-17)
[<c020d6a9>] kobject_register+0x51/0x53
[<c026d961>] bus_add_driver+0x49/0xb4
[<c030da15>] i2c_add_driver+0x52/0xc1
[<d09b2df2>] msp3400_init_module+0xa/0xd [msp3400]
[<c01328d0>] sys_init_module+0x13c/0x282
[<c0103f6b>] syscall_call+0x7/0xb
ivtv: Encoder revision: 0x02040024
ivtv: Decoder revision: 0x02020023
ivtv: Configuring WinTV PVR 350 card with 9 streams
ivtv: Create DMA stream 0
ivtv: Create DMA stream 1
ivtv: Create stream 2
ivtv: Create DMA stream 3
ivtv: Create stream 4
ivtv: Create DMA stream 5
ivtv: Create stream 6
ivtv: Create stream 7
ivtv: Create DMA stream 8
ivtv: Setting Tuner 1
tuner: type set to 1 (Philips PAL_I (FI1246 and compatibles)) by ivtv 
i2c driver #0
ivtv: Setting audio matrix to input 3, output 1
ivtv: Switching standard to PAL.
saa7115: decoder set norm PAL
saa7115: set audio: 0x01
saa7127: Setting Encoder Video Standard
saa7127: Set PAL Video Mode
saa7127: Selecting PAL video Standard
ivtv: Initialized WinTV PVR 350, card #0
ivtv: ====================  END INIT IVTV  ====================