[mythtv-users] Mandrake 9.2 setup (btaudio)

[RJV]

I'm attempting to set up a MythTV box under Mandrake 9.2

Currently, I'm attempting to get btaudio to work.  I've got a WinTV card
with the appropriate MSP chip onboard.

I'm trying to get btaudio working prior to setting up MythTV.

btaudio doesn't load automatically, but something called "tvaudio" does.

I've tried adding btaudio by using insmod - but I'm getting no sound.
I've also tried rmmod bttv then modprobe btaudio and modprobe bttv.  Here
is what dmesg shows:

bttv0: unloading
btaudio: driver version 0.7 loaded [digital+analog]
btaudio: Bt878 (rev 2) at 00:0b.1, irq: 17, latency: 32, mmio: 0xe3000000
btaudio: using card config "default"
btaudio: registered device dsp1 [digital]
btaudio: registered device dsp2 [analog]
btaudio: registered device mixer1
bttv: driver version 0.7.107 loaded
bttv: using 4 buffers with 2080k (8320k total) for capture
bttv: Host bridge is VIA Technologies, Inc. VT8377 [KT400 AGP] Host Bridge
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 2) at 00:0b.0, irq: 17, latency: 32, mmio: 0xe3002000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: BT878(Hauppauge (bt878)) [card=10,autodetected]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
msp34xx: init: chip=MSP3430G-A1, has NICAM support
msp3410: daemon started
tuner: chip found @ 0xc2
bttv0: Hauppauge eeprom: model=61111, tuner=Temic 4036FY5 (8), radio=no
bttv0: using tuner=8
tuner: type set to 8 (Temic NTSC (4036 FY5))
bttv0: i2c: checking for MSP34xx @ 0x80... found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips:
tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54
(PV951),ta8874z
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL can sleep, using XTAL (28636363).

Now, if I do a listing in /dev, I have /dev/dsp dsp1 and dsp2.  I also
have /dev/mixer and mixer1.

however, if I load up xawtv and then run "aplay /dev/dsp1" - I get
no sound.

Examination of kmix shows that there is only my soundcard mixer.

I know btaudio is difficult to get set up.  Any help would be appreciated.


-- RJV --					..ooOO miracle at procyon.com

-- Institution of Postgraduate Education - Graduation 2001
-- Institution of Undergraduate Education - Alumnus 1997

The opinions expressed in any email originating from this account are the
sole opinions of the author.  They do not reflect the opinions or policies
of any institution or individuals other than myself.