<div dir="ltr"><div dir="ltr"><br></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sun, 29 May 2022 at 20:12, Klaas de Waal <<a href="mailto:klaas.de.waal@gmail.com">klaas.de.waal@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr"><div dir="ltr"><br></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sun, 29 May 2022 at 12:34, Piotr Oniszczuk <<a href="mailto:piotr.oniszczuk@gmail.com" target="_blank">piotr.oniszczuk@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><br>
<br>
> Wiadomość napisana przez Matthias Thyroff <<a href="mailto:matthias@thyroff.net" target="_blank">matthias@thyroff.net</a>> w dniu 28.05.2022, o godz. 21:09:<br>
> <br>
> Am 28.05.22 um 16:24 schrieb Piotr Oniszczuk:<br>
>> Klaas, Matthias,<br>
>> <br>
>> I have unicable system @my home working perfectly last 6 years (4 tuners, 35-50 recordings per day; usually 3..8 concurrent recordings tested 16 w/o any problems; months without failed recording)<br>
>> <br>
>> IIRC unicable setup is very simple:<br>
>> <br>
>> in mythtv-setup<br>
>> 1. select "2. capture cards"<br>
>> 2. select "new capture card" then press Enter<br>
>> 3. go by arrow keys to "New Capture Card"<br>
>> 4. press right arrow<br>
>> 5. select DVB-T/S/C...., press enter<br>
>> 6. press right arrow<br>
>> 7. go down by arrow keys to "DiSEqC...", press right arrow<br>
>> 8. in Device type select "Unicable", press enter<br>
>> 9. press right arrow, you should see "Unicable configuration"<br>
>> 10. press right arrow to enter Unicable config<br>
>> 11. set "Userband" to 0 (for your first tuner, 1 for second etc) (*)<br>
>> 12. set "Frequency" to 1210 for your first tuner (1420 for second, 1680 for third; 2040 for 4th)<br>
>> 13. leave "pincode" to -1<br>
>> 14. "Repeat Count" - start with 3 (**)<br>
>> 15. Set "Device Type" to LNB<br>
>> 16. press Esc, then select "save"<br>
>> <br>
>> You can repeat steeps 2...15 for rest of yours tuners - but remember set appropriate values in steeps: 11 and 12<br>
>> <br>
>> (*)<br>
>> Some unicable vendors are using enumeration starting from 0, some others starting from 1<br>
>> Try first with 0 and if your first tuner will not work ok - try starting with 1<br>
>> <br>
>> <br>
>> (**)<br>
>> Some unicable vendors - for reliable operation - requiring multiple resending tune commands to get reliable each userband PLL setting in unicable unit at myth tuning time.<br>
>> This is case i.e. with mine Inverto unicable unit: when myth BE sends single tune command - i have 5-10% of failed tunings.<br>
>> But when I do 3 sends (send + 2 resends) - then failed tunings are goinf down to approx 0.01%.<br>
>> Some time ago - i addeed to mythv capability of resends: when you set repeat count in steep 14 to value above 10, myth will enter resending mode with N-10 resends. So i.e. setting to 13 will cause 3 sends of tune command at tuning stage<br>
>> <br>
>> Happy watching!<br>
>>  <br>
>> <br>
>> _______________________________________________<br>
>> mythtv-users mailing list<br>
>> <a href="mailto:mythtv-users@mythtv.org" target="_blank">mythtv-users@mythtv.org</a><br>
>> <a href="http://lists.mythtv.org/mailman/listinfo/mythtv-users" rel="noreferrer" target="_blank">http://lists.mythtv.org/mailman/listinfo/mythtv-users</a><br>
>> <a href="http://wiki.mythtv.org/Mailing_List_etiquette" rel="noreferrer" target="_blank">http://wiki.mythtv.org/Mailing_List_etiquette</a><br>
>> MythTV Forums: <a href="https://forum.mythtv.org" rel="noreferrer" target="_blank">https://forum.mythtv.org</a><br>
>> <br>
> Hi Piotr,<br>
> <br>
> that gives me hope! :-)<br>
> <br>
> I have done all as you say and man I have a hard time getting it to work. I have tried back and forth a million things and times, and still I can't rule out (1) failing cards (2) failing antenna (3) failing cables (4) failing drivers (5) failing mythtv<br>
> <br>
> because it is so inconsistent. When it works, as you say, tuning fails frequently especially at the first tune,  but resending 9 or 15 times has not done anything, it seems I need to change channel back and forth to get a lock.<br>
> <br>
> What cards are you using?<br>
> <br>
> Cheers,<br>
> <br>
> Matthias<br>
> <br>
> <br>
<br>
Matthias,<br>
<br>
Ok - then indeed we have checklist to do: <br>
(1) failing antenna<br>
(2) failing cables <br>
(3) failing cards <br>
(4) failing drivers<br>
(5) failing mythtv DVB subsys<br>
(6) failing LNB unicable implementation<br>
(7) failing mythtv unicable implementation<br>
<br>
<br>
Without steep-by-steep elimination we will not able to find root case and fix.<br>
<br>
Lest start with list+order like i'm proposing<br>
<br>
(1) failing antena/ (2)failing cables:<br>
can yo go for test with no Unicable and make sure LNB+dish are positioned ok?<br>
Ideally will be i.e. with borrowed SAT receiver and: tune to SAT channel + verify signal strength + S/N are good enough for reliable reception?<br>
(borrow receiver from friend, neighbourhood, etc)<br>
<br>
If above will show you all is ok - the we can go with (3)<br>
Install on you BE software to watch SAT TV.<br>
best will be sw. provided by card vendor eventually any well known SAT watching software.<br>
Alternatively You can try with tools scanning SAT transponders:<br>
<a href="https://www.linuxtv.org/wiki/index.php/Frequency_scan#Comparison_of_DVB_frequency_scanning_commandline_utilities" rel="noreferrer" target="_blank">https://www.linuxtv.org/wiki/index.php/Frequency_scan#Comparison_of_DVB_frequency_scanning_commandline_utilities</a><br>
<a href="https://www.linuxtv.org/wiki/index.php/Scan" rel="noreferrer" target="_blank">https://www.linuxtv.org/wiki/index.php/Scan</a><br>
<a href="https://www.linuxtv.org/wiki/index.php/Dvbscan" rel="noreferrer" target="_blank">https://www.linuxtv.org/wiki/index.php/Dvbscan</a><br>
<br>
If above will be ok - we already know: (1)/(2)/(3) are ok.<br>
If in above test you will use target kernel+target card drivers - then steep (4) also can be marked as ok.<br>
<br>
So we can go with (5):<br>
configure mythtv to use standard LNB (no any Unicable) and try tune to some FTA channels.<br>
<br>
If (5) will go ok - then we can try (7): setup myth to use unicable and try.<br>
<br>
If it will fail then:<br>
<br>
-borrow somewhere SAT receiver capable to do Unicable, configure Unicable and verify is it working OK.<br>
<br>
If such SAT receiver will work - then out root cause is (7)<br>
If such SAT receiver will now work - then out root cause is (6)<br>
<br>
let me know how it goes for you!<br>
<br><br></blockquote><div>I have my setup with a "DUR-line UK 124-3L dCSS - Unicable LNB" working correctly! I can now make a perfect channel scan with mythtv-setup.</div><div>The difference is that I replaced the single tuner DVBSky S950-C card with a dual tuner DVBSky S952 V3.</div><div>At this moment I only use one tuner of the two available; when the new splitter arrives (special for Unicable, DC coupled and 5-2400MHz) I will test with both tuners.</div><div>For now it looks that the card does make the difference.</div><div><br></div></div></div></blockquote><div>I have now documented the procedure in the Channel Scanning WIki pages, similar to the description of Piotr, but with more words.</div><div>With this procedure my DVBSky S952 cards do work OK with Unicable.</div><div><br></div><div>After that I went back to the DVBSky S950-C card, configured with the same procedure.</div><div>This card still does not work reliably, with behavior similar to what Matthias describes.</div><div><br></div><div>To get an indication whether this is a MythTV software problem I have now also used minisatip (see <a href="https://github.com/catalinii/minisatip">https://github.com/catalinii/minisatip</a>) to handle the S950-C card; MythTV is configured to use the Sat>IP protocol to talk to the minisatip server. This configuration has similar behavior and similar problems. This makes it unlikely, although not impossible, that it is a bug in the MythTV Unicable implementation.</div><div>Note that when the S950-C card is connected to a normal ("legacy") LNB the card works OK.</div><div><br></div><div>@Mathias, it would be interesting to know if your tuner cards do work OK when using the minisatip server to control the cards with Unicable.</div><div><a class="gmail_plusreply" id="plusReplyChip-1" href="mailto:piotr.oniszczuk@gmail.com" tabindex="-1">@Piotr Oniszczuk</a>  it would also be interesting which tuner cards you have tested with Unicable.<br></div><div> </div><div>Thanks,</div><div>Klaas.</div><div><br></div><div><br></div><div><br></div></div></div>