<div dir="ltr">Assuming you are using v31 it is a good idea to create a new video source and then do a new channel scan. The reason for this is that sometimes old channel data prevents new data from being stored correctly. With a new video source and a "Full Scan" it should just work.<div>There have been reports that it is needed to set the modulation type of this type of tuner to DVB-T2 but this should be the default for a new installation.<div><br><div>About the multirec, in the mythtv-setup page Input Connections / Interactions between Inputs there is a "Schedule as Group" option. If this option is checked, and it is by default on a new install, then multirec is enabled. You can specify the initial amount of tuners (the first option) but you can leave that at the default of 2.</div><div><br></div><div>For everything else you want to know about channel scanning you might want to read Wiki page <a href="https://www.mythtv.org/wiki/Channel_Scanning">https://www.mythtv.org/wiki/Channel_Scanning</a></div><div><br></div></div></div><div>Klaas.</div><div><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, 2 Feb 2021 at 22:32, John Pilkington <<a href="mailto:johnpilk222@gmail.com">johnpilk222@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">On 02/02/2021 20:47, John Pilkington wrote:<br>
> On 02/02/2021 19:50, Simon Hobson wrote:<br>
>> I've just pulled out my old HVR-1250 (IIRC) cards and replaced them <br>
>> with a new QuadHD card. It's working fine, giving me 4 tuners (and <br>
>> eliminating the recording errors due to poor signal*), but I've a <br>
>> couple of issues :<br>
>><br>
>><br>
>> I can't find where to configure multi-rec.<br>
>> That's one of those "so long sine I last did it, can't remember how I <br>
>> did it" things.<br>
>> According to <br>
>> <a href="https://www.mythtv.org/wiki/Record_multiple_channels_from_one_multiplex" rel="noreferrer" target="_blank">https://www.mythtv.org/wiki/Record_multiple_channels_from_one_multiplex</a> it's <br>
>> just a case of going into the advanced settings and setting the number <br>
>> of virtual tuners, and that's how I vaguely remember doing it. But <br>
>> it's just not there in my setup.<br>
>> It's shown as Silicon Labs Si2168 and subtype DVB-T2 - but no advanced <br>
>> settings option.<br>
> <br>
> mythtv-setup > Input connections > select device > interactions between <br>
> inputs > max recordings<br>
>><br>
>><br>
>> It's not finding any DVB-T2 muxes.<br>
>> I should be getting at least 1 T2 mux, according to <br>
>> <a href="https://ukfree.tv/transmitters/tv/Winter_Hill" rel="noreferrer" target="_blank">https://ukfree.tv/transmitters/tv/Winter_Hill</a> the PSB3/BBCB mux should <br>
>> be on 585.8MHz. It's not found by a full scan, nor by a "scan an <br>
>> existing transport and find any linked ones" option. I suspect Com7 on <br>
>> 746MHz will be out of band for my aerial so I'm not bothered about that.<br>
>><br>
>><br>
>> Any thoughts ?<br>
>><br>
>> Simon<br>
>><br>
>><br>
>> * having two cards I needed to use a splitter - so lost a lot of <br>
>> signal strength. It was fine when I first set it up here, but has <br>
>> degraded to the point where I had to remove the splitter and disable <br>
>> one of the cards - thus hitting limitations with only one real tuner.<br>
> <br>
> Perhaps a bit late now, but a preamp before the splitter ought to <br>
> maintain the signal to noise ratio as well as boosting the level.  Newer <br>
> tuners do this on-chip.<br>
> <br>
> I forget which release you have been using, but a *lot* of work has gone <br>
> into DVB channel scanning recently.<br>
> <br>
> HTH<br>
> <br>
> John P<br>
<br>
And I ought to have picked up on your T2 query.  iirc the DVB-T2 <br>
transports carry the links to DVB-T,  but there are no links to the <br>
DVB-T2 ones;  and in my experience the UK Free channel info has often <br>
not been kept up to date.  I have found the 'manual tuning' menu of my <br>
TV helpful in warning when a 'difficult' mux is undergoing maintenance; <br>
scanning in the evening has worked best.  Of course that will only work <br>
if Myth and your TV can receive simultaneously.<br>
<br>
<a href="https://www.cai.org.uk/index.php/contact/dtt-freeview-updates" rel="noreferrer" target="_blank">https://www.cai.org.uk/index.php/contact/dtt-freeview-updates</a><br>
<br>
<br>
<br>
<br>
<br>
_______________________________________________<br>
mythtv-users mailing list<br>
<a href="mailto:mythtv-users@mythtv.org" target="_blank">mythtv-users@mythtv.org</a><br>
<a href="http://lists.mythtv.org/mailman/listinfo/mythtv-users" rel="noreferrer" target="_blank">http://lists.mythtv.org/mailman/listinfo/mythtv-users</a><br>
<a href="http://wiki.mythtv.org/Mailing_List_etiquette" rel="noreferrer" target="_blank">http://wiki.mythtv.org/Mailing_List_etiquette</a><br>
MythTV Forums: <a href="https://forum.mythtv.org" rel="noreferrer" target="_blank">https://forum.mythtv.org</a><br>
</blockquote></div>