<div dir="ltr"><div dir="ltr"><div class="gmail_quote"><div dir="ltr">On Sat, Oct 13, 2018 at 10:00 AM Peter Bennett <<a href="mailto:pb.mythtv@gmail.com">pb.mythtv@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
  
    
  
  <div bgcolor="#FFFFFF"><br>
    <div class="gmail-m_4794267282931539777moz-cite-prefix">On 10/13/2018 08:36 AM, Richard Shaw
      wrote:<br>
    </div>
    <blockquote type="cite">
      
      <div dir="ltr">
        <div dir="ltr">
          <div dir="ltr">I'm finally getting tired of getting incomplete
            information, especially season and episode data, from DD.
            It's causing quite a few recordings to not show up in Plex
            which we're using on Roku TVs instead of having to build
            mini-frontends. 
            <div><br>
            </div>
            <div>I'm following the directions from the wiki[1] but I'm
              not sure I'm getting the whole story...</div>
            <div><br>
            </div>
            <div>So i'm pretty much at the point of deleting and
              re-adding channels since the IDs are in a different
              format. If I was just doing OTA I would see if I could
              manually translate them but with Cables 200+ channels, I'm
              not going to that much trouble. </div>
            <div><br>
            </div>
          </div>
        </div>
      </div>
    </blockquote>
    Another advantage to re-adding them is that you get icons for all
    the channels.<br>
    <blockquote type="cite">
      <div dir="ltr">
        <div dir="ltr">
          <div dir="ltr">
            <div>So far the side effects are:</div>
            <div><br>
            </div>
            <div>1. Existing recordings will show the wrong channel?</div>
          </div>
        </div>
      </div>
    </blockquote>
    This may or may not happen. By default the chanid is set up as a
    number with format xyyy where x is the source id and yyy is the
    channel number. Sometimes this scheme can get messed up by manual
    additions, duplicate channels etc. If your existing channels follow
    this scheme, they should be the same after re-adding and then
    existing recordings will show the correct channel.<br>
    <blockquote type="cite">
      <div dir="ltr">
        <div dir="ltr">
          <div dir="ltr">
            <div>2. The wiki doesn't mention if I'll have to re-setup
              all my recording rules...</div>
            <div><br>
            </div>
          </div>
        </div>
      </div>
    </blockquote>
    That should not be necessary unless you have channel specific rules.
    If the chanid and station id stay the same these should also be ok.
    Personally I never use channel specific rules. Regardless, you
    should check upcoming recordings to see if they are still working
    after the change.<br>
    <blockquote type="cite">
      <div dir="ltr">
        <div dir="ltr">
          <div dir="ltr">
            <div>I currently have two sources</div>
            <div><br>
            </div>
            <div>[1] OTA</div>
            <div>[2] Comcast</div>
            <div><br>
            </div>
            <div>Is it possible to setup a 3 & 4 with
              tv_grab_zz_sdjson_sqlite and have both until everything
              that was recorded on 1 & 2 expire?<br>
            </div>
            <div><br>
            </div>
          </div>
        </div>
      </div>
    </blockquote>
    I cannot see that this would work or any benefit to it. You may be
    able to leave the old sources in place unconnected to any capture
    card in case you want to switch back, but I am not sure whether this
    will work.</div></blockquote><div><br></div><div>I only mentioned that due to #1 above, if that's not a problem then there is no reason, however, the wiki does not appear to be up to date. It tells me that I need to delete and re-add my channels, but in the specific instructions under  "Deleting and re-adding channels" it says to go into the channel editor (which would be too slow) and in the next sentence says to select video source and delete.</div><div><br></div><div>Then it says to un mythfilldatabase but after I did that it refused to run saying there were no video sources configured. </div><div><br></div><div>I used mythtv-setup to set them up but its very "clunky" the way it works but per the instructions I thought this the sqlite grabber had to be setup from the command line but nothing in the instructions seemed to actually insert the video sources.</div><div><br></div><div>I'm a pretty experienced linux user, been running MythTV for 10 years, and a Fedora packager for 8. If this doesn't make sense to me I can't be the only one confused by this process.</div><div><br></div><div>Also I've been doing this all as root because the backend user mythtv doesn't have a shell. I'm assuming I'll have to move the resulting .xmltv and .SD files to /etc/mythtv when complete.</div><div><br></div><div>Thanks,</div><div>Richard</div></div></div></div>