<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=utf-8">
</head>
<body text="#000000" bgcolor="#FFFFFF">
<div class="moz-cite-prefix">On 07/08/18 17:03, Douglas Peale wrote:<br>
</div>
<blockquote type="cite"
cite="mid:a73f4a3c-fabf-8b7b-b896-3f28d34300cf@comcast.net">
<pre wrap="">On 08/07/2018 01:48 AM, John Pilkington wrote:
</pre>
<blockquote type="cite">
<pre wrap="">On 07/08/18 06:29, Douglas Peale wrote:
</pre>
<blockquote type="cite">
<pre wrap="">What happened to the ability to scan a range of channels?
I have two antennas aimed about 20 degrees apart. Both see all channels from both directions, but each sees the channels from
its direction much better than the other direction.
After a full scan, I must delete all channels from the other direction to prevent MythTV from choosing a source with bad
reception.
While doing this, I accidentally deleted one channel. I tried to manually add it back, but I was not able to select ATSC as the
type as it does not appear in the selection list.
So I tried a full scan, assuming I could choose which ones to add by selecting manual. Nope. there is now way to skip one
channel. You can skip a type, but not a single channel.
Worse, I had edited all of the channel numbers from xx_yy to xx.yy. MythTV changed them all back to xx_yy.
I can't even use mythweb to edit the channels. It will display them, but when I try to save the changes, it gives me an error,
and displays the old values.
Rant complete.
</pre>
</blockquote>
<pre wrap="">
I haven't tried anything like this. but I think you need to define two Video Sources in mythtv-setup, one for each antenna.
Then in the Channel scanning/editing section you should be able to scan separately for each, using a 'full scan' or perhaps,
after a first run,
'all known transports.'
_______________________________________________
mythtv-users mailing list
<a class="moz-txt-link-abbreviated" href="mailto:mythtv-users@mythtv.org">mythtv-users@mythtv.org</a>
<a class="moz-txt-link-freetext" href="http://lists.mythtv.org/mailman/listinfo/mythtv-users">http://lists.mythtv.org/mailman/listinfo/mythtv-users</a>
<a class="moz-txt-link-freetext" href="http://wiki.mythtv.org/Mailing_List_etiquette">http://wiki.mythtv.org/Mailing_List_etiquette</a>
MythTV Forums: <a class="moz-txt-link-freetext" href="https://forum.mythtv.org">https://forum.mythtv.org</a>
</pre>
</blockquote>
<pre wrap="">I actually am already doing this. I have three video sources defined, one each for my three antennas.
The problem is that I had accidentally deleted a channel, so none of the scans would add it back except the full scan.
Unfortunately, that goes and adds all the channels from two antennas, a few from the third, and changes the channel number on
all of them.
I end up with 54 channels for which I need to edit or delete every one. To edit 54_1 to 54.1, requires 11 keystrokes in myth
backend setup. It is a little easier in mythweb, but mythweb was not working at the time.
</pre>
<br>
<fieldset class="mimeAttachmentHeader"></fieldset>
<br>
<pre wrap="">_______________________________________________
mythtv-users mailing list
<a class="moz-txt-link-abbreviated" href="mailto:mythtv-users@mythtv.org">mythtv-users@mythtv.org</a>
<a class="moz-txt-link-freetext" href="http://lists.mythtv.org/mailman/listinfo/mythtv-users">http://lists.mythtv.org/mailman/listinfo/mythtv-users</a>
<a class="moz-txt-link-freetext" href="http://wiki.mythtv.org/Mailing_List_etiquette">http://wiki.mythtv.org/Mailing_List_etiquette</a>
MythTV Forums: <a class="moz-txt-link-freetext" href="https://forum.mythtv.org">https://forum.mythtv.org</a>
</pre>
</blockquote>
<p>The channel editor in Mythsetup allows individual transponder
scanning, so if you get the details from <a
moz-do-not-send="true"
href="https://en.kingofsat.net/freqs.php?&pos=28.2E&standard=All&ordre=freq&filtre=Clear">https://en.kingofsat.net/freqs.php?&pos=28.2E&standard=All&ordre=freq&filtre=Clear
<br>
</a></p>
<p>its pretty simple to restore deleted items without sucking in the
lot.<br>
</p>
</body>
</html>