<p dir="ltr"></p>
<p dir="ltr">On Sep 4, 2016 8:21 AM, "Hika van den Hoven" <<a href="mailto:hikavdh@gmail.com">hikavdh@gmail.com</a>> wrote:<br>
><br>
> Hoi Adrian,<br>
><br>
> Sunday, September 4, 2016, 4:56:09 PM, you wrote:<br>
><br>
><br>
><br>
> > On Fri, Sep 2, 2016 at 5:34 PM, Adrian Hains <<a href="mailto:ahains@gmail.com">ahains@gmail.com</a>> wrote:<br>
><br>
> > Hi,<br>
> > I'm a MythTv newbie attempting to get this dvr up and running. I<br>
> > have a mac desktop running OSX El Capitan, and I have installed a<br>
> > fresh mythbuntu VM of version 16.04.1.<br>
><br>
><br>
> > Going through the MythTV Setup:<br>
> > 1. Left all settings in General at defaults<br>
> > 2. Added the HDHOMERUN under Capture Cards. It was found on the network, easy-peasy.<br>
> > 3. Video sources: setup schedules direct account, and chose the<br>
> > only data direct lineup option (it looked correct for my area).<br>
> > 4. Input connections: chose the HDHR and schedules direct, and<br>
> > tried "Fetch channels from listing source". I noticed in the MythTV<br>
> > Setup Terminal output that it skipped the fetch because I had not<br>
> > yet done a channel scan. Tried a channel scan, and this is where I<br>
> > am now stuck as all channels with good signal strength show<br>
> > Status:locked, but give "Timed out, no channels".<br>
><br>
><br>
> > I have a few screen shots from my mythbuntu running in VirtualBox:<br>
><br>
><br>
> > 1. Scan settings at default:<br>
> > <a href="https://goo.gl/photos/DVRx3gHH1mFQ4mWS8">https://goo.gl/photos/DVRx3gHH1mFQ4mWS8</a> <br>
><br>
><br>
> > 2. Scan in progress - all channels with lock are giving "Timed out,<br>
> > no channels" (the scan gave the no channels message for 100% of the<br>
> > channels that had a strong enough signal to lock):<br>
> > <a href="https://goo.gl/photos/CiCEV1bMo4uzCkhT9">https://goo.gl/photos/CiCEV1bMo4uzCkhT9</a><br>
><br>
><br>
><br>
> > 3. "hdhomerun_config 1045A33A scan 0" from a terminal on the same VM successfully finds channels:<br>
> > <a href="https://goo.gl/photos/Bz5ov8x3417XFmQw8">https://goo.gl/photos/Bz5ov8x3417XFmQw8</a><br>
><br>
><br>
><br>
> > And outside of this VM, on the mac that is hosting it, I can view<br>
> > video from this same hdhomerun successfully:<br>
> > <a href="https://goo.gl/photos/Huj2BEU8uZSyoiJN8">https://goo.gl/photos/Huj2BEU8uZSyoiJN8</a><br>
><br>
><br>
><br>
> > I would be very grateful for any suggestions of what I can try next to get past this error.<br>
> > thanks!<br>
> > -Adrian<br>
><br>
><br>
><br>
><br>
> > Additional info:<br>
><br>
> > I installed a new mythbuntu VM of version 14.04 to see if 16.04.1<br>
> > had some kind of problem, and had the same result -- all channels<br>
> > that acquired lock in the scan said "Timed out, no channels".<br>
><br>
><br>
> > I then tried install mythbuntu 16.04.01 on a PC directly rather<br>
> > than a VM, and the channel scan was successful and DID NOT have the<br>
> > problem. This PC and the original mac are on the same network and<br>
> > subnet, so I think the issue may have been related to the VM<br>
> > networking somehow. I had configured the osx firewall to allow<br>
> > VirtualBox, so I'm not sure what exactly was the root cause.<br>
><br>
><br>
> > So I might futz around with the VirtualBox network config, or I<br>
> > might just try to install mythbuntu natively on the mac.<br>
> > Thanks,<br>
> > Adrian<br>
><br>
> Firewall! What kind of network connection did you select in vbox? NAT?<br>
><br>
> Tot mails,<br>
>   Hika                            mailto:<a href="mailto:hikavdh@gmail.com">hikavdh@gmail.com</a><br>
><br>
> "Zonder hoop kun je niet leven<br>
> Zonder leven is er geen hoop<br>
> Het eeuwige dilemma<br>
> Zeker als je hoop moet vernietigen om te kunnen overleven!"<br>
><br>
> De lerende Mens<br>
><br>
> </p>
<p dir="ltr">Hika,<br>
I had left it at the default, which was NAT. I just tested changing this to bridged adaptor a few minutes ago, and now the scan is finding channels!<br>
Thanks!<br>
-Adrian<br>
</p>