<div dir="ltr"><br><div class="gmail_extra"><br><div class="gmail_quote">On Sun, Oct 4, 2015 at 5:50 AM, Mike Perkins <span dir="ltr"><<a href="mailto:mikep@randomtraveller.org.uk" target="_blank">mikep@randomtraveller.org.uk</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div class="HOEnZb"><div class="h5">On 04/10/15 07:24, Joseph Fry wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
On Tue, Sep 29, 2015 at 6:33 PM, Richard Woelk <<a href="mailto:richardwoelk@gmail.com" target="_blank">richardwoelk@gmail.com</a>><br>
wrote:<br>
<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
When my HDPVR 1212 power supplies started going, I cut the ends off and<br>
connected them to a hard drive molex from inside the computer. This works<br>
well, and the HDPVRs are actually a lot more stable.<br>
It is probably a good idea to put a fuse in it.<br>
<br>
</blockquote>
<br>
I am just finishing rewiring my mythtv setup.<br>
<br>
I have 4 HDPVR's, and 2 usb ports (powering a Raspberry Pi and a little 8<br>
port switch) on the 5v rail and 4 Cisco STB's on the 12v rail all running<br>
off a standard ATX powersupply (think it's 400w).<br>
<br>
Based on the current ratings of all of the equipment's wallwarts, I am well<br>
under the rated current on both rails, and I doubt I would ever come close<br>
to the theoretical max since the equipment typically draws well under the<br>
maximum rating of it's wall wart.<br>
<br>
There is absolutely no doubt that my ATX power supply is more efficient<br>
than 10 wall warts would be, and the quality of the power is so much better.<br>
<br>
Took a little while to wire all of the barrel plugs and USB ports...<br>
everything is wired to Molex splitters, so I can change the power supply<br>
easily if it ever fails.<br>
<br>
</blockquote></div></div>
Be aware that things can work the other way around as well - your PSU may fail to produce the right voltages and/or regulate them well enough if the load is too low.<br>
<br>
Most PSUs require some kind of minimum loading on one of the rails, usually the +5v rail, in order to provide a reference voltage the other rails can use.<br>
<br>
Of course, every PSU is made different, YMMV etc.</blockquote><div><br></div><div>Definitely not a problem for me... but even if I had a PSU like that I think I have plenty of load:</div><div><br></div><div>5V</div><div>4 x HDPVR = 8 Amps = 40W</div><div>1 x RPI = 1 Amp = 5W</div><div>1x switch = 1 Amp = 5W</div><div><br></div><div>12V</div><div>4 x STB = 8 Amps = 96W</div><div><br></div><div>Peak load would be about 150W.  I suspect that typical load will be far less, but definitely above any minimum.</div><div><br></div></div></div></div>