<p dir="ltr"><br>
On Jan 20, 2015 1:16 PM, "glen" <<a href="mailto:glenb@glenb.us">glenb@glenb.us</a>> wrote:<br>
><br>
><br>
><br>
> On Tue, Jan 20, 2015 at 10:08 AM, Daryl McDonald <<a href="mailto:darylangela@gmail.com">darylangela@gmail.com</a>> wrote:<br>
>><br>
>><br>
>> On Jan 20, 2015 12:38 PM, "Eric Sharkey" <<a href="mailto:eric@lisaneric.org">eric@lisaneric.org</a>> wrote:<br>
>> ><br>
>> > On Tue, Jan 20, 2015 at 10:25 AM, Daryl McDonald <<a href="mailto:darylangela@gmail.com">darylangela@gmail.com</a>> wrote:<br>
>> > > On Tue, Jan 20, 2015 at 9:43 AM, glen <<a href="mailto:glenb@glenb.us">glenb@glenb.us</a>> wrote:<br>
>> > >> On Tue, Jan 20, 2015 at 6:32 AM, Daryl McDonald <<a href="mailto:darylangela@gmail.com">darylangela@gmail.com</a>><br>
>> > >> wrote:<br>
>> > >><br>
>> > >> Greetings Mythizens, I just added a new HDHomerun dual to my system, all<br>
>> > >> seemed well. The system recognized the device found the device ID, I used an<br>
>> > >> existing Input Connection, first, and then scanned for channels, and still<br>
>> > >> system status shows "tuner error" for the HDHomerun, even after restarting<br>
>> > >> the FE. What have I missed?<br>
>> > >><br>
>> > >> TIA  Daryl<br>
>> > >><br>
>> > >><br>
>> > >><br>
>> > >> if he existing input you used was not done with the same tuner than the<br>
>> > >> hdhr has no tuning parameters and you would see that error. you probably<br>
>> > >> have to create a new one and scan again<br>
>> > ><br>
>> > > Thanks for the quick response Glen, sounded great and easy to do, but no<br>
>> > > luck, I created the new input connection, rescanned, and filled in the<br>
>> > > XMLID's, restarted the FE and still the error status. Any other ideas?<br>
>> ><br>
>> > I think he meant create a new tuner, not a new input connection.<br>
>> ><br>
>> > Eric<br>
>> > _______________________________________________<br>
>> > mythtv-users mailing list<br>
>> > <a href="mailto:mythtv-users@mythtv.org">mythtv-users@mythtv.org</a><br>
>> > <a href="http://lists.mythtv.org/mailman/listinfo/mythtv-users">http://lists.mythtv.org/mailman/listinfo/mythtv-users</a><br>
>> > <a href="http://wiki.mythtv.org/Mailing_List_etiquette">http://wiki.mythtv.org/Mailing_List_etiquette</a><br>
>> > MythTV Forums: <a href="https://forum.mythtv.org">https://forum.mythtv.org</a><br>
>><br>
>> I did create a new tuner, and a new input connection and did a rescan and set max recordings to 4 (2&2) and I remain stumped<br>
><br>
><br>
> this is a dual hdhr using either over the air or clear qam.... i assume. how are you naming the channel numbers are they unique to whatever else you have named. maybe try deleting the new things you added and start over. in the scan it asks you for channel numbers or accept suggested. use unique channel numbers and then add xmltvids and get some listings data to the channels and it should tune. if not maybe some kind of firewall issue on the network tuner.<br>
><br>
> _______________________________________________<br>
> mythtv-users mailing list<br>
> <a href="mailto:mythtv-users@mythtv.org">mythtv-users@mythtv.org</a><br>
> <a href="http://lists.mythtv.org/mailman/listinfo/mythtv-users">http://lists.mythtv.org/mailman/listinfo/mythtv-users</a><br>
> <a href="http://wiki.mythtv.org/Mailing_List_etiquette">http://wiki.mythtv.org/Mailing_List_etiquette</a><br>
> MythTV Forums: <a href="https://forum.mythtv.org">https://forum.mythtv.org</a><br>
><br></p>
<p dir="ltr">It is a dual using an antenna I use channel numbers as they scan in. They are the same as my other FTA tuner (PCI) I did mythfilldatabase after adding the card, etc. Not home right now, but I will try unique numbers/names later on. Firewall may be an issue, so I went in and dedicated port 5000 for hdhr, I'll look into the firewall deeper later too.</p>