<div dir="ltr">i have posted earlier about this but had to deal with other "irl" issues soon after, preventing<br>me from putting as much time & effort as i should have.<br><br>i can now try again, hoping to solve what i feel is a "pebkac" issue, as i am sure that the<br>root of the problem is incorrectly specified parameters to get mythtv to properly scan some fta<br>sats.<br><br>to recap, in a nutshell: have built what i hope will be a pvr to record pbs fta programming. am using the latest version of mythbuntu (14.04), or win8.1 (for validation the hardware works<br>and the sat can indeed be scanned), depending on the hard drive inserted in the machine.<br><br>the fta tuner is a tbs 6982 (<a href="http://www.tbsdtv.com/products/tbs6982-dvb-s2-dual-tuner-pcie-card.html" target="_blank">http://www.tbsdtv.com/products/tbs6982-dvb-s2-dual-tuner-pcie-card.html</a>).<br><br>have two dishes, each with a universal lnb, one pointed to 125w, the other to 87w.<br>the dishes are connected to a living-room fta receiver (geosatpro microhd) through a 4 port diseqc <br>switch (<a href="http://worldwidesatellites.com/4x1-best-germany-diseqc-switch-bhigh-qualityb-p-787.html" target="_blank">http://worldwidesatellites.com/4x1-best-germany-diseqc-switch-bhigh-qualityb-p-787.html</a>). a second coax run from each dish goes to the pc that i talk about in this e-mail/posting, through its own diseqc switch (same brand).<br><br>i have been somewhat successful in win8.1, either sat can be scanned and i can "play" the channels that have been identified.<br><br>on myth, i have had less success.  myth sees something, but cannot lock on the signal and scan in the channels.  this happens on both sat.  below are the parameters i have based my entries on:<br><br>lnb type: avenger universal pll (dual outputs). <br>    (<a href="http://worldwidesatellites.com/avenger-pll322s-twin-ku-pll-lnbf-p-700.html" target="_blank">http://worldwidesatellites.com/avenger-pll322s-twin-ku-pll-lnbf-p-700.html</a>)<br><br>sat and transponder:<br>(125w)<br>    tp freq.:    12180<br>    polarity:    vertical<br>    symbol rate:    3000<br>    mod sys:    dvb-s2<br>    fec:        3/4<br>    modulation:    8psk<br><br>(87w)<br>    tp freq.:    11812<br>    polarity:    h<br>    symbol rate:    11149<br>    mod. sys.:    dvb-s2<br>    fec:        3/5<br>    modulaton:    8psk<br><br>here are links for 3 screenshots of the parameters used in mythtv.<br>87w<br>    <a href="http://i60.tinypic.com/2ymae79.jpg">http://i60.tinypic.com/2ymae79.jpg</a><br>125w<br>    <a href="http://i61.tinypic.com/2h3o235.jpg">http://i61.tinypic.com/2h3o235.jpg</a><br>lnb<br>    <a href="http://i59.tinypic.com/264p646.jpg">http://i59.tinypic.com/264p646.jpg</a><br>"inversion" and "roll-off" were set to "auto", since i don't know what proper values should be.<br><br>so i know the dishes are properly aligned and all, as i can use the living room receiver to watch pbs.  i also know the cabling to the pc and the machine itself work, as i've had some success in win8.1.  i'm trying to eliminate the possibility that i simply didn't set something quite right in myth.  quite sure it's fairly obvious, but i can't quite see it.<br><br>so does anyone see what is my (stupid) mistake?<br>thanks.<br><br></div>