<div dir="ltr">Try these two at the command line, see if either of them plays back the wav file. You should have that wav file, it comes with alsa...<br><br>aplay -D plughw:0,2 /usr/share/sounds/alsa/Front_Right.wav<br><br>
aplay -D plughw:0,7 /usr/share/sounds/alsa/Front_Right.wav<br><br>If you have the same issue I did, one will play, the other will not...<br></div><div class="gmail_extra"><br><br><div class="gmail_quote">On Mon, Nov 11, 2013 at 5:03 PM, Leif Pihl <span dir="ltr"><<a href="mailto:leif@pihl.us" target="_blank">leif@pihl.us</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div style="word-wrap:break-word">Colin Mackay: <div><br></div><div>Yup. I got very similar output, here it is: <div><br>
</div><div><span style="font-family:arial,helvetica,sans-serif;white-space:pre-wrap">**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC892 Analog [ALC892 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
</span><span style="font-family:arial,helvetica,sans-serif;white-space:pre-wrap">card 0: PCH [HDA Intel PCH], device 1: ALC892 Digital [ALC892 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0</span></div><div><span style="font-family:arial,helvetica,sans-serif;white-space:pre-wrap">card 0: PCH [HDA Intel PCH], device 2: HDMI 0 [HDMI 0] </span></div><div class="im"><div><span style="font-family:arial,helvetica,sans-serif;white-space:pre-wrap"> Subdevices: 1/1
Subdevice #0: subdevice #0</span></div></div><div><span style="font-family:arial,helvetica,sans-serif;white-space:pre-wrap">card 0: PCH [HDA Intel PCH], device 7: HDMI 1 [HDMI 1]</span></div><div class="im"><div><span style="font-family:arial,helvetica,sans-serif;white-space:pre-wrap"> Subdevices: 1/1
Subdevice #0: subdevice #0</span></div><div><br></div><div><br></div><div><br></div><div><br></div></div><div>Eric Sharkey: </div><div><br></div><div>I haven't gotten to read that web site just yet. </div><span class="HOEnZb"><font color="#888888"><div>
<br></div><div><br></div><div><br></div><div>LP</div></font></span><div><div class="h5"><div><br></div><div><br></div><div><br></div><div><br></div><div><br></div><div><br></div><div><br><div><div>On Nov 11, 2013, at 10:05 AM, Colin Mackay wrote:</div>
<br><blockquote type="cite"><div dir="ltr">Here's something to try... Lets see what devices Linux see's. Try this command:<br><br><b>aplay -l</b><br><br>This should give you something along the lines of:<br><br>
<br><pre><span style="font-family:arial,helvetica,sans-serif">**** List of PLAYBACK Hardware Devices ****
card 0: Intel [HDA Intel], device 0: ALC889A Analog [ALC889A Analog]
Subdevices: 0/1
Subdevice #0: subdevice #0
card 0: Intel [HDA Intel], device 1: ALC889A Digital [ALC889A Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: Intel [HDA Intel], device 3: HDMI 0 [HDMI 0]
Subdevices: 0/1
Subdevice #0: subdevice #0</span></pre><br></div><div class="gmail_extra"><br><br><div class="gmail_quote">On Mon, Nov 11, 2013 at 10:23 AM, Leif Pihl <span dir="ltr"><<a href="mailto:leif@pihl.us" target="_blank">leif@pihl.us</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">See below<br>
<div><div><br>
<br>
<br>
On Nov 11, 2013, at 9:04 AM, Leif Pihl wrote:<br>
> On Nov 11, 2013, at 8:33 AM, Eric Sharkey wrote:<br>
>> On Sun, Nov 10, 2013 at 9:03 PM, Leif Pihl <<a href="mailto:leif@pihl.us" target="_blank">leif@pihl.us</a>> wrote:<br>
>>> On the screen right now is a series of 16 bar graphs.<br>
>>> At the top center, it's labeled AlsaMixer v1.0.26 (maybe 28 - it's a fuzzy photo that I took; I'm in a different room.)<br>
>>> Upper left corner says the following:<br>
>>> Card: HDA Intel PCH<br>
>>> Chip: Intel PantherPoint HDMI<br>
>><br>
>> Ok. That means that PulseAudio is not active.<br>
><br>
> Hmmm... What would it say if PulseAudio WAS active?<br>
><br>
><br>
>> You are using the HDMI connection on the motherboard itself, not a<br>
>> discrete PCI Express graphics card, is that correct?<br>
><br>
> Yes - motherboard's HDMI interface.<br>
> I suspected the software was going to be tough enough,<br>
> so I wanted the hardware to be as simple (and low cost - eh) as possible and/or practical.<br>
><br>
><br>
>>> The bar graphs show this data, going left to right:<br>
>>> Master: 41 (bar is roughly 41-ish percent up from the bottom)<br>
>><br>
>> That's a little low. I'd recommend that you bump that to 100. I'm<br>
>> not sure if it really matters with HDMI, though.<br>
><br>
> I'll see if I can figure it out.<br>
> I'm assuming that if I select it in some way (tab?) that I can use the up-arrow key.<br>
><br>
><br>
>> Underneath the bar, does it show OO or MM? You want it to say OO (you<br>
>> can toggle this with the m key).<br>
>><br>
>> Eric<br>
><br>
><br>
><br>
> With the SIX exceptions listed below, most of the bar graphs did show the "OO" characters you were looking for.<br>
><br>
>> For those of you who archive the past messages, this is a response to messages dating from 11/08/13.<br>
> << CLIP >><br>
>> The bar graphs show this data, going left to right:<br>
<br>
<br>
</div></div>I was able to adjust the first ten and last two bar graphs.<br>
<br>
Of the first ten, I set them all to 100%<br>
All four of those that I could not adjust started with "S/PD...".<br>
(I've NOT changed their mode from "OO" to "MM" as of yet.)<br>
The last two (Rear Mic's) could be adjusted, but I left them at 0%.<br>
<br>
<br>
Still no change regarding the Audio output.<br>
<br>
<br>
What does the "S/PD..." and so forth stand for?<br>
Should I change their modes from "OO" to "MM", or leave them alone?<br>
<div><br>
<br>
<br>
>> Master: 41 (bar is roughly 41-ish percent up from the bottom)<br>
>> Headphone: 100<>100 (bar is at 100%)<br>
>> PCM: 100<>100 (bar is at 100%)<br>
> (BLANK)<br>
><br>
>> Front: 100<>100 (bar is at 100%)<br>
>> Front Mi: 0<>0 (bar is at 0%)<br>
> MM<br>
><br>
>> Front Mi: 0<>0 (bar is at 0%)<br>
> (BLANK)<br>
><br>
>> Surround: 100<>100 (bar is at 100%)<br>
>> Center: 100 (bar is at 100%)<br>
>> LFE: 0<>0 (bar is at 100%)<br>
>> Line: 0<>0 (bar is at 0%)<br>
> MM<br>
><br>
>> S/PDIF: (blank) (bar is NON Existant)<br>
>> S/PDIF D: (blank) (bar is NON Existant)<br>
>> S/PD 1: (blank) (bar is NON Existant)<br>
>> S/PD 2: (blank) (bar is NON Existant)<br>
>> Rear Mic: 0<>0 (bar is at 0%)<br>
> MM<br>
><br>
>> Rear Mic: 0<>0 (bar is at 0%)<br>
> MM<br>
<br>
<br>
</div>See above.<br>
<div><div>_______________________________________________<br>
mythtv-users mailing list<br>
<a href="mailto:mythtv-users@mythtv.org" target="_blank">mythtv-users@mythtv.org</a><br>
<a href="http://www.mythtv.org/mailman/listinfo/mythtv-users" target="_blank">http://www.mythtv.org/mailman/listinfo/mythtv-users</a><br>
</div></div></blockquote></div><br></div>
_______________________________________________<br>mythtv-users mailing list<br><a href="mailto:mythtv-users@mythtv.org" target="_blank">mythtv-users@mythtv.org</a><br><a href="http://www.mythtv.org/mailman/listinfo/mythtv-users" target="_blank">http://www.mythtv.org/mailman/listinfo/mythtv-users</a><br>
</blockquote></div><br></div></div></div></div></div><br>_______________________________________________<br>
mythtv-users mailing list<br>
<a href="mailto:mythtv-users@mythtv.org">mythtv-users@mythtv.org</a><br>
<a href="http://www.mythtv.org/mailman/listinfo/mythtv-users" target="_blank">http://www.mythtv.org/mailman/listinfo/mythtv-users</a><br>
<br></blockquote></div><br></div>