<META HTTP-EQUIV="Content-Type" CONTENT="text/html; charset=iso-8859-1">
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 3.2//EN">
<HTML>
<HEAD>
<META NAME="Generator" CONTENT="MS Exchange Server version 6.5.7638.1">
<TITLE>Re: [mythtv-users] Air2PC ATSC Getting it to work</TITLE>
</HEAD>
<BODY>
<DIV id=idOWAReplyText86766 dir=ltr>
<DIV dir=ltr><FONT face=Arial color=#000000 size=2>The scan completed but found
no services. I have a 32db HDTV RCA antenna sitting on my computer desk at the
front corner of my house. Any suggestions on getting a signal.</FONT></DIV>
<DIV dir=ltr><FONT face=Arial color=#000000 size=2></FONT> </DIV></DIV>
<DIV id=idSignature65300 dir=ltr>
<DIV><FONT face=Arial color=#000000 size=2>
<DIV><FONT face=Arial size=2>Thank You</FONT></DIV>
<DIV><FONT face=Arial size=2>Melvin Cureton</FONT></DIV>
<DIV><FONT face=Arial size=2><A
href="mailto:melvincureton@melcrys.com">melvincureton@melcrys.com</A></FONT></DIV></FONT></DIV></DIV>
<DIV dir=ltr><BR>
<HR tabIndex=-1>
<FONT face=Tahoma size=2><B>From:</B> mythtv-users-bounces@mythtv.org on behalf
of Meatwad<BR><B>Sent:</B> Thu 12/28/2006 11:07 PM<BR><B>To:</B> Discussion
about mythtv<BR><B>Subject:</B> Re: [mythtv-users] Air2PC ATSC Getting it to
work<BR></FONT><BR></DIV>
<DIV>
<P><FONT size=2>Melvin J. Cureton wrote:<BR>> I have an Air2PC card
installed. I have the firmware (dvb-fe-nxt2002.fw)<BR>> in
/usr/lib/hotplug/firmware. When I do dmesg I get the
following:<BR>> <BR>> b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital
TV receiver chip loaded<BR>> successfully<BR>> flexcop-pci: will use the
HW PID filter.<BR>> flexcop-pci: card revision 2<BR>> ACPI: PCI Interrupt
Link [LNKB] enabled at IRQ 18<BR>> ACPI: PCI Interrupt 0000:01:04.0[A] ->
Link [LNKB] -> GSI 18 (level,<BR>> high) -> IRQ 201<BR>> DVB:
registering new adapter (FlexCop Digital TV device).<BR>> b2c2-flexcop: MAC
address = 00:d0:d7:30:1a:96<BR>> b2c2-flexcop: i2c master_xfer failed<BR>>
ivtv: no version for "struct_module" found: kernel tainted.<BR>> ivtv:
==================== START INIT IVTV ====================<BR>> ivtv:
version 0.8.2 (tagged release) loading<BR>> ivtv: Linux version:
2.6.18-1.2868.fc6 SMP mod_unload 686 REGPARM<BR>> 4KSTACKS gcc-4.1<BR>>
ivtv: In case of problems please include the debug info between<BR>>
ivtv: the START INIT IVTV and END INIT IVTV lines, along with<BR>>
ivtv: any module options, when mailing the ivtv-users mailinglist.<BR>>
b2c2-flexcop: i2c master_xfer failed<BR>> b2c2-flexcop: i2c master_xfer
failed<BR>> nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err ==
-121)<BR>> Unknown/Unsupported NXT chip: 00 00 00 00 00<BR>> b2c2-flexcop:
i2c master_xfer failed<BR>> lgdt330x: i2c_read_demod_bytes: addr 0x59 select
0x02 error (ret == -121)<BR>> bcm3510: Revision: 0x1, Layer: 0xb.<BR>>
b2c2-flexcop: found the bcm3510 at i2c address: 0x0f<BR>> DVB: registering
frontend 0 (Broadcom BCM3510 VSB/QAM frontend)...<BR>> b2c2-flexcop:
initialization of 'Air2PC/AirStar 2 ATSC 1st generation'<BR>> at the 'PCI'
bus controlled by a 'FlexCopIIb' complete<BR>> <BR>> And with lspci
-v:<BR>> <BR>> 01:04.0 Network controller: Techsan Electronics Co Ltd
B2C2 FlexCopII<BR>> DVB chip / Technisat SkyStar2 DVB card (rev
02)<BR>> Subsystem: Techsan
Electronics Co Ltd B2C2 FlexCopII DVB chip /<BR>> Technisat SkyStar2 DVB
card<BR>> Flags: bus master,
slow devsel, latency 64, IRQ
201<BR>> Memory at ff4f0000
(32-bit, non-prefetchable)
[size=64K]<BR>> I/O ports at
cc00 [size=32]<BR>> Now it say it loaded the card successfully but in ivtv it
says:<BR>> <BR>> b2c2-flexcop: i2c master_xfer failed<BR>>
b2c2-flexcop: i2c master_xfer failed<BR>> nxt200x: nxt200x_readbytes: i2c
read error (addr 0x0a, err == -121)<BR>> Unknown/Unsupported NXT chip: 00 00
00 00 00<BR>> b2c2-flexcop: i2c master_xfer failed<BR>> Is this
normal?<BR><BR>Is this a newer HD5000 AirStar Technisat card? If so, I get
those<BR>messages too. Doesn't seem to be a problem for me. Elsewhere in
dmesg<BR>are the lines:<BR><BR> b2c2-flexcop: found the lgdt3303 at
i2c address: 0x59<BR> DVB: registering frontend 1 (LG Electronics
LGDT3303 VSB/QAM<BR> Frontend)...<BR> b2c2-flexcop:
initialization of 'Air2PC/AirStar 2 ATSC 3rd generation<BR> (HD5000)' at
the 'PCI' bus controlled by a 'FlexCopIIb' complete<BR><BR>If you see that, the
kernel has the proper driver and you should be good<BR>to go.<BR><BR>> Also,
how the hell do I create a channels.conf for azap and dvbscan and<BR>> other
scanning programs? I have the attached from atennaweb.org. How do<BR>> I
change that info into a properly formatted channel.conf file. Is there<BR>> a
template or layout directions somewhere?<BR><BR>I just do a complete scan after
properly configuring mythsetup<BR>with a data
source.<BR>_______________________________________________<BR>mythtv-users
mailing list<BR>mythtv-users@mythtv.org<BR><A
href="http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users">http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users</A><BR></FONT></P></DIV>
</BODY>
</HTML>