<META HTTP-EQUIV="Content-Type" CONTENT="text/html; charset=iso-8859-1">
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 3.2//EN">
<HTML>
<HEAD>
<META NAME="Generator" CONTENT="MS Exchange Server version 6.5.7638.1">
<TITLE>[mythtv-users] Air2PC ATSC Getting it to work</TITLE>
</HEAD>
<BODY>
<DIV id=idOWAReplyText90202 dir=ltr>
<DIV dir=ltr><FONT face=Arial color=#000000 size=2>I put that firmware in
/usr/lib/hotplug/firmware. Do you get the following message too?</FONT></DIV>
<DIV dir=ltr><FONT face=Arial size=2></FONT> </DIV>
<DIV dir=ltr>bcm3510: could not load firmware (dvb-fe-bcm3510-01.fw): -2</DIV>
<DIV dir=ltr><FONT face=Arial color=#000000 size=2></FONT> </DIV></DIV>
<DIV id=idSignature63703 dir=ltr>
<DIV><FONT face=Arial color=#000000 size=2>
<DIV><FONT face=Arial size=2>Thank You</FONT></DIV>
<DIV><FONT face=Arial size=2>Melvin Cureton</FONT></DIV>
<DIV><FONT face=Arial size=2><A
href="mailto:melvincureton@melcrys.com">melvincureton@melcrys.com</A></FONT></DIV></FONT></DIV></DIV>
<DIV dir=ltr><BR>
<HR tabIndex=-1>
<FONT face=Tahoma size=2><B>From:</B> mythtv-users-bounces@mythtv.org on behalf
of Alan Marchiori<BR><B>Sent:</B> Fri 12/29/2006 9:04 AM<BR><B>To:</B>
mythtv-users@mythtv.org<BR><B>Subject:</B> [mythtv-users] Air2PC ATSC Getting it
to work<BR></FONT><BR></DIV>
<DIV>
<P><FONT size=2> Melvin J. Cureton wrote:<BR>> I have an Air2PC card
installed. I have the firmware (dvb-fe-nxt2002.fw)<BR>> in
/usr/lib/hotplug/firmware. When I do dmesg I get the following:<BR>..<BR>>
nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)<BR>>
Unknown/Unsupported NXT chip: 00 00 00 00 00<BR>> b2c2-flexcop: i2c
master_xfer failed<BR>> lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02
error (ret == -121)<BR>> bcm3510: Revision: 0x1, Layer: 0xb.<BR>>
b2c2-flexcop: found the bcm3510 at i2c address: 0x0f<BR>> DVB: registering
frontend 0 (Broadcom BCM3510 VSB/QAM frontend)...<BR>..<BR>> nxt200x:
nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)<BR>>
Unknown/Unsupported NXT chip: 00 00 00 00 00<BR>> b2c2-flexcop: i2c
master_xfer failed<BR><BR>I have the same setup. And had the same
problem. Notice it detects<BR>the bcm3510 chip, you need to install the
driver for that chip in the<BR>firmware directory.<BR><BR>try this:<BR><A
href="http://www.linuxtv.org/download/firmware/dvb-fe-bcm3510-01.fw">http://www.linuxtv.org/download/firmware/dvb-fe-bcm3510-01.fw</A><BR><BR>This
is the only firmware file I have installed and it works fine. I<BR>do
always get the i2c master_xfer failed errors also, if someone could<BR>tell me
how to get rid of them it would be
nice.<BR>_______________________________________________<BR>mythtv-users mailing
list<BR>mythtv-users@mythtv.org<BR><A
href="http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users">http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users</A><BR></FONT></P></DIV>
</BODY>
</HTML>