<META HTTP-EQUIV="Content-Type" CONTENT="text/html; charset=iso-8859-1">
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN"><HTML DIR=ltr><HEAD></HEAD><BODY>
<DIV id=idOWAReplyText13103 dir=ltr>
<DIV dir=ltr><FONT face=Arial color=#000000 size=2>I have an Air2PC card
installed. I have the firmware (dvb-fe-nxt2002.fw) in /usr/lib/hotplug/firmware.
When I do dmesg I get the following:</FONT></DIV>
<DIV dir=ltr><FONT face=Arial size=2></FONT> </DIV>
<DIV dir=ltr>b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip
loaded successfully<BR>flexcop-pci: will use the HW PID filter.<BR>flexcop-pci:
card revision 2<BR>ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18<BR>ACPI:
PCI Interrupt 0000:01:04.0[A] -> Link [LNKB] -> GSI 18 (level, high) ->
IRQ 201<BR>DVB: registering new adapter (FlexCop Digital TV
device).<BR>b2c2-flexcop: MAC address = 00:d0:d7:30:1a:96<BR>b2c2-flexcop: i2c
master_xfer failed<BR>ivtv: no version for "struct_module" found: kernel
tainted.<BR>ivtv: ==================== START INIT IVTV
====================<BR>ivtv: version 0.8.2 (tagged release)
loading<BR>ivtv: Linux version: 2.6.18-1.2868.fc6 SMP mod_unload 686
REGPARM 4KSTACKS gcc-4.1<BR>ivtv: In case of problems please include the
debug info between<BR>ivtv: the START INIT IVTV and END INIT IVTV lines,
along with<BR>ivtv: any module options, when mailing the ivtv-users
mailinglist.<BR>b2c2-flexcop: i2c master_xfer failed<BR>b2c2-flexcop: i2c
master_xfer failed<BR>nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err
== -121)<BR>Unknown/Unsupported NXT chip: 00 00 00 00 00<BR>b2c2-flexcop: i2c
master_xfer failed<BR>lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02
error (ret == -121)<BR>bcm3510: Revision: 0x1, Layer: 0xb.<BR>b2c2-flexcop:
found the bcm3510 at i2c address: 0x0f<BR>DVB: registering frontend 0 (Broadcom
BCM3510 VSB/QAM frontend)...<BR>b2c2-flexcop: initialization of 'Air2PC/AirStar
2 ATSC 1st generation' at the 'PCI' bus controlled by a 'FlexCopIIb'
complete</DIV>
<DIV dir=ltr> </DIV>
<DIV dir=ltr>And with lspci -v:</DIV>
<DIV dir=ltr> </DIV>
<DIV dir=ltr>01:04.0 Network controller: Techsan Electronics Co Ltd B2C2
FlexCopII DVB chip / Technisat SkyStar2 DVB card (rev
02)<BR> Subsystem: Techsan Electronics
Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB
card<BR> Flags: bus master, slow
devsel, latency 64, IRQ 201<BR> Memory
at ff4f0000 (32-bit, non-prefetchable)
[size=64K]<BR> I/O ports at cc00
[size=32]<BR></DIV>
<DIV dir=ltr>Now it say it loaded the card successfully but in ivtv it
says:</DIV>
<DIV dir=ltr> </DIV>
<DIV dir=ltr>b2c2-flexcop: i2c master_xfer failed<BR>b2c2-flexcop: i2c
master_xfer failed<BR>nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err
== -121)<BR>Unknown/Unsupported NXT chip: 00 00 00 00 00<BR>b2c2-flexcop: i2c
master_xfer failed<BR></DIV>
<DIV dir=ltr>Is this normal?</DIV>
<DIV dir=ltr> </DIV>
<DIV dir=ltr>Also, how the hell do I create a channels.conf for azap and dvbscan
and other scanning programs? I have the attached from atennaweb.org. How do I
change that info into a properly formatted channel.conf file. Is there a
template or layout directions somewhere?</DIV>
<DIV dir=ltr><FONT face=Arial color=#000000 size=2></FONT> </DIV></DIV>
<DIV id=idSignature89770 dir=ltr>
<DIV><FONT face=Arial color=#000000 size=2>
<DIV><FONT face=Arial size=2>Thank You</FONT></DIV>
<DIV><FONT face=Arial size=2>Melvin Cureton</FONT></DIV>
<DIV><FONT face=Arial size=2><A
href="mailto:melvincureton@melcrys.com">melvincureton@melcrys.com</A></FONT></DIV></FONT></DIV></DIV></BODY></HTML>