Walter,<br /><br />I've pulled the ffmpeg source from atrpms and it
installed,  But I cann't find where it installed to so I can configure and
build it.  What was the configuration used to build it?<br /><br
/>Chris<br /><br
/><alexjfisher@gmail.com><philledwards@gmail.com><mythtv-users@mythtv.org><philledwards@gmail.com><walter.hofstetter@netwho.com><mythtv-users@mythtv.org>&gt;
<br />&gt; Chris,<br />&gt; <br />&gt; I'm currently struggling as well
with the myth2ipod script.<br />&gt; I took the source-rpm of ffmpeg from
atrpms and recompiled ffmpeg to<br />&gt; assure the aac (codec) is
enabled.<br />&gt; <br />&gt; I found that I can convert mpeg2 videos to
mp4 (ipod) when starting<br />&gt; ffmpeg mnually.<br />&gt; (In the
meantime, Axel (atrpms) was very helpful and updated the ffmpeg<br />&gt;
package on atrpms with the using the source).<br />&gt; <br />&gt; I tried
to nail down my problem when starting &quot;nuvexport -debug&quot;.<br
/>&gt; (nuvexport is called form myth2ipod).<br />&gt; In the debug mode
nuvexport provides a list commands executed, so you<br />&gt; just do the
conversion step by step, using two shells.<br />&gt; In my case the error
was caused by a SIGFPE (floating point error),<br />&gt; casued by
ffmpeg.....<br />&gt; <br />&gt; I'll investigate a bit further to check
if this has to do with the fifos<br />&gt; created by nuvexport.<br />&gt;
<br />&gt; I'm not sure how to get a hold of people coding nuvexport, but
I'll also<br />&gt; post this behavior on the ffmpeg-devel list, because
on the end ffmgeg<br />&gt; falls over the FPE issue...<br />&gt; <br
/>&gt; -Walter<br />&gt; <br />&gt; <br />&gt; <br />&gt; jmail wrote:<br
/>&gt;&gt; I have a Myth 20 system on a Fedora Core 4 I installed from the
ATRPMS<br />&gt;&gt; following Jerod's guide.<br />&gt;&gt; I've been
trying to get myth2ipod to install and run.  I've installed<br />&gt;&gt;
myth2ipod but when I execute it the log file says that ffmpeg exited<br
/>&gt;&gt; early.<br />&gt;&gt; I suspect I don't have ffmpeg built right.
   How do I build ffmpeg with<br />&gt;&gt; the right properties enabled
starting from a yum installed machine.<br />&gt;&gt; I've read Jerod's
spec file posted in Dec.  but I don't know what to do<br />&gt;&gt; with
this.  Any detailed install instructions would be greatly<br />&gt;&gt;
appreciated.<br />&gt;&gt;<br />&gt;&gt; Chris<br />&gt;&gt;
_______________________________________________<br />&gt;&gt; mythtv-users
mailing list<br />&gt;&gt; mythtv-users@mythtv.org<br />&gt;&gt;
http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users)<br />&gt;&gt;<br
/>&gt;&gt;</mythtv-users@mythtv.org></walter.hofstetter@netwho.com></philledwards@gmail.com></mythtv-users@mythtv.org></philledwards@gmail.com></alexjfisher@gmail.com><br
/>