<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
<meta content="text/html;charset=ISO-8859-1" http-equiv="Content-Type">
</head>
<body bgcolor="#ffffff" text="#000000">
Steven Adeff wrote:
<blockquote
cite="mid42785b900609080802r3af55122ka17fdea8b31ff78c@mail.gmail.com"
type="cite">
<pre wrap="">On 9/8/06, Calvin Harrigan <a class="moz-txt-link-rfc2396E" href="mailto:charriglists@bellsouth.net"><charriglists@bellsouth.net></a> wrote:
</pre>
<blockquote type="cite">
<pre wrap="">Steven Adeff wrote:
</pre>
<blockquote type="cite">
<pre wrap="">On 9/8/06, Stef Coene <a class="moz-txt-link-rfc2396E" href="mailto:stef.coene@docum.org"><stef.coene@docum.org></a> wrote:
</pre>
<blockquote type="cite">
<pre wrap="">On Friday 08 September 2006 14:54, Steven Adeff wrote:
</pre>
<blockquote type="cite">
<pre wrap="">On 9/8/06, Stef Coene <a class="moz-txt-link-rfc2396E" href="mailto:stef.coene@docum.org"><stef.coene@docum.org></a> wrote:
</pre>
<blockquote type="cite">
<pre wrap="">On Friday 08 September 2006 01:10, Steven Adeff wrote:
</pre>
<blockquote type="cite">
<pre wrap="">nope, no go. The power button on the front definitely works, but the
power button on the remote does nothing. I have an LC16M
</pre>
</blockquote>
<pre wrap="">Make sure the receiver has power even if the frontend is down.
</pre>
</blockquote>
<pre wrap="">so like a battery is needed? hrmm. more trouble than its worth I fear.
</pre>
</blockquote>
<pre wrap="">No, the power supply has a special output wire that has always power. Even
when the frontend is down. Just make sure that your power supply has such
output and connect the receiver to it.
</pre>
</blockquote>
<pre wrap="">ahh, I don't believe my power supply has that =(
</pre>
</blockquote>
<pre wrap="">If you have an ATX powersupply, you do...
</pre>
</blockquote>
<pre wrap=""><!---->
How do I identify which plug it is then?
</pre>
</blockquote>
Sorry I didn't follow this thread closely but I hope I can help.<br>
ATX power supply does keep the 5V Standby ready even if the computer is
"off", unless u flipped the switch behind the supply. If your receiver
is connected to the USB, but it doesn't get any power when the computer
is off, it should worth to check the jumpers on the motherboard. Most
mothers board has a jumper to specify which power source to connect to
the 5V rail of the USB, may be you should try another one.<br>
<br>
Take Asus M2NPV-VM as an example..It's manual URL:<br>
<a class="moz-txt-link-freetext" href="ftp://dlsvr03.asus.com/pub/ASUS/mb/socketAM2/M2NPV-VM/e2527_m2npv-vm.pdf">ftp://dlsvr03.asus.com/pub/ASUS/mb/socketAM2/M2NPV-VM/e2527_m2npv-vm.pdf</a><br>
Mirror:
<a class="moz-txt-link-freetext" href="ftp://dlsvr02.asus.com/pub/ASUS/mb/socketAM2/M2NPV-VM/e2527_m2npv-vm.pdf">ftp://dlsvr02.asus.com/pub/ASUS/mb/socketAM2/M2NPV-VM/e2527_m2npv-vm.pdf</a><br>
Page 31. Most likely u need +5VSB.<br>
<br>
I hope this helps<br>
Take a look at this one..<br>
</body>
</html>