<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 TRANSITIONAL//EN">
<HTML>
<HEAD>
<META HTTP-EQUIV="Content-Type" CONTENT="text/html; CHARSET=UTF-8">
<META NAME="GENERATOR" CONTENT="GtkHTML/3.6.1">
</HEAD>
<BODY>
Hello all,<BR>
<BR>
I'm trying to set up a myth system with a PVR-500, however running into some problems. I haven't even attempted to install myth yet... just trying to get this card to work. I'm using Gentoo Linux and following the instructions on their wiki (<A HREF="http://gentoo-wiki.com/HARDWARE_PVR_500_Setup)">http://gentoo-wiki.com/HARDWARE_PVR_500_Setup)</A><BR>
<BR>
However, when I modprobe ivtv, I get this failures in my dmesg output. It seems as if modules aren't loading. Where do I get them? Can someone please help me with this? (I would post my kernel config, but it's too large to post -- I tried to post the most relevant sections)<BR>
<BR>
Thanks!!<BR>
<BR>
~Jeff<BR>
jeff@plotzke.com<BR>
<BR>
dmesg output:<BR>
<BR>
ivtv: version 0.4.2 (tagged release) loading<BR>
ivtv: Linux version: 2.6.15-gentoo-r5 SMP gcc-3.4<BR>
ivtv: In case of problems please include the debug info between<BR>
ivtv: the START INIT IVTV and END INIT IVTV lines, along with<BR>
ivtv: any module options, when mailing the ivtv-users mailinglist.<BR>
ivtv0: Autodetected WinTV PVR 150 card (cx23416 based)<BR>
ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 19 (level, low) -> IRQ 209<BR>
ivtv0: i2c attach to card #0 ok [client=eeprom, addr=50]<BR>
tda9887 1-0043: chip found @ 0x86 (ivtv i2c driver #0)<BR>
ivtv0: i2c attach to card #0 ok [client=tda9887, addr=43]<BR>
tuner 1-0060: TEA5767 detected.<BR>
tuner 1-0060: chip found @ 0xc0 (ivtv i2c driver #0)<BR>
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=60]<BR>
tuner 1-0060: type set to 62 (Philips TEA5767HN FM Radio)<BR>
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)<BR>
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]<BR>
ivtv0 warning: i2c client addr: 0x50 not found for command 0x0!<BR>
ivtv0: Error -19 reading Hauppauge eeprom.<BR>
ivtv0: Possible causes: the tveeprom module was not loaded, or<BR>
ivtv0: the eeprom kernel module was loaded before the tveeprom module.<BR>
ivtv0: Failed to load module cx25840<BR>
ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c!<BR>
ivtv0: Failed to load module wm8775<BR>
ivtv0: Could not detect tuner standard, defaulting to NTSC.<BR>
ivtv0: Detected a TEA5767 radio tuner. Enabling radio support.<BR>
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)<BR>
ivtv0: Encoder revision: 0x02050032<BR>
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)<BR>
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)<BR>
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)<BR>
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)<BR>
ivtv0: Create encoder radio stream<BR>
tuner 1-0061: type set to 68 (Philips TUV1236D ATSC/NTSC dual in)<BR>
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40085618!<BR>
ivtv0 warning: i2c client addr: 0x44 not found for command 0xc0045627!<BR>
ivtv0 warning: i2c client addr: 0x1b not found for command 0x40046d11!<BR>
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40046d11!<BR>
tuner 1-000a: i2c i/o error: rc == -121 (should be 2)<BR>
tuner 1-000a: i2c i/o error: rc == -121 (should be 2)<BR>
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40085618!<BR>
ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c!<BR>
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40045613!<BR>
tuner 1-000a: i2c i/o error: rc == -121 (should be 2)<BR>
tuner 1-000a: i2c i/o error: rc == -121 (should be 2)<BR>
ivtv0 warning: i2c client addr: 0x1b not found for command 0x402c5639!<BR>
ivtv0 warning: i2c client addr: 0x44 not found for command 0x402c5639!<BR>
ivtv0 warning: i2c client addr: 0x44 not found for command 0x40045612!<BR>
ivtv0 warning: i2c client addr: 0x44 not found for command 0xc008561c!<BR>
ivtv0: Initialized WinTV PVR 150, card #0<BR>
ivtv: ====================== NEXT CARD ======================<BR>
ivtv1: Autodetected WinTV PVR 150 card (cx23416 based)<BR>
ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 16 (level, low) -> IRQ 201<BR>
ivtv1: i2c attach to card #1 ok [client=eeprom, addr=50]<BR>
tda9887 2-0043: chip found @ 0x86 (ivtv i2c driver #1)<BR>
ivtv1: i2c attach to card #1 ok [client=tda9887, addr=43]<BR>
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #1)<BR>
ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]<BR>
ivtv1 warning: i2c client addr: 0x50 not found for command 0x0!<BR>
ivtv1: Error -19 reading Hauppauge eeprom.<BR>
ivtv1: Possible causes: the tveeprom module was not loaded, or<BR>
ivtv1: the eeprom kernel module was loaded before the tveeprom module.<BR>
ivtv1: Failed to load module cx25840<BR>
ivtv1 warning: i2c client addr: 0x44 not found for command 0xc008561c!<BR>
ivtv1: Failed to load module wm8775<BR>
ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)<BR>
ivtv1: Encoder revision: 0x02050032<BR>
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)<BR>
ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)<BR>
ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)<BR>
ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)<BR>
tuner 2-0061: type set to 68 (Philips TUV1236D ATSC/NTSC dual in)<BR>
ivtv1 warning: i2c client addr: 0x44 not found for command 0x40085618!<BR>
ivtv1 warning: i2c client addr: 0x44 not found for command 0xc0045627!<BR>
ivtv1 warning: i2c client addr: 0x1b not found for command 0x40046d11!<BR>
ivtv1 warning: i2c client addr: 0x44 not found for command 0x40046d11!<BR>
tuner 2-000a: i2c i/o error: rc == -121 (should be 2)<BR>
tuner 2-000a: i2c i/o error: rc == -121 (should be 2)<BR>
ivtv1 warning: i2c client addr: 0x44 not found for command 0x40085618!<BR>
ivtv1 warning: i2c client addr: 0x44 not found for command 0xc008561c!<BR>
ivtv1 warning: i2c client addr: 0x44 not found for command 0x40045613!<BR>
tuner 2-000a: i2c i/o error: rc == -121 (should be 2)<BR>
tuner 2-000a: i2c i/o error: rc == -121 (should be 2)<BR>
ivtv1 warning: i2c client addr: 0x1b not found for command 0x402c5639!<BR>
ivtv1 warning: i2c client addr: 0x44 not found for command 0x402c5639!<BR>
ivtv1 warning: i2c client addr: 0x44 not found for command 0x40045612!<BR>
ivtv1 warning: i2c client addr: 0x44 not found for command 0xc008561c!<BR>
ivtv1: Initialized WinTV PVR 150, card #1<BR>
ivtv: ==================== END INIT IVTV ====================<BR>
<BR>
<BR>
/etc/modules.d/ivtv:<BR>
<BR>
alias char-major-81 videodev<BR>
alias char-major-81-0 ivtv<BR>
alias char-major-81-1 ivtv<BR>
alias char-major-61 lirc_i2c<BR>
#add above ivtv lirc_dev lirc_i2c<BR>
<BR>
options ivtv ivtv_std=1 tuner=68,68<BR>
option cx25840 cx25840_fw="/lib/modules/HcwMakoC.ROM"<BR>
<BR>
<BR>
Kernel .config:<BR>
<BR>
#<BR>
# I2C support<BR>
#<BR>
CONFIG_I2C=m<BR>
CONFIG_I2C_CHARDEV=m<BR>
<BR>
#<BR>
# I2C Algorithms<BR>
#<BR>
CONFIG_I2C_ALGOBIT=m<BR>
# CONFIG_I2C_ALGOPCF is not set<BR>
# CONFIG_I2C_ALGOPCA is not set<BR>
<BR>
#<BR>
# I2C Hardware Bus support<BR>
#<BR>
# CONFIG_I2C_ALI1535 is not set<BR>
# CONFIG_I2C_ALI1563 is not set<BR>
# CONFIG_I2C_ALI15X3 is not set<BR>
# CONFIG_I2C_AMD756 is not set<BR>
# CONFIG_I2C_AMD8111 is not set<BR>
# CONFIG_I2C_I801 is not set<BR>
# CONFIG_I2C_I810 is not set<BR>
# CONFIG_I2C_PIIX4 is not set<BR>
# CONFIG_I2C_NFORCE2 is not set<BR>
# CONFIG_I2C_PARPORT_LIGHT is not set<BR>
# CONFIG_I2C_PROSAVAGE is not set<BR>
# CONFIG_I2C_SAVAGE4 is not set<BR>
# CONFIG_SCx200_ACB is not set<BR>
# CONFIG_I2C_SIS5595 is not set<BR>
# CONFIG_I2C_SIS630 is not set<BR>
# CONFIG_I2C_SIS96X is not set<BR>
# CONFIG_I2C_STUB is not set<BR>
# CONFIG_I2C_VIA is not set<BR>
CONFIG_I2C_VIAPRO=m<BR>
# CONFIG_I2C_VOODOO3 is not set<BR>
# CONFIG_I2C_PCA_ISA is not set<BR>
<BR>
#<BR>
# Multimedia devices<BR>
#<BR>
CONFIG_VIDEO_DEV=m<BR>
<BR>
#<BR>
# Video For Linux<BR>
#<BR>
<BR>
#<BR>
# Video Adapters<BR>
#<BR>
CONFIG_VIDEO_BT848=m<BR>
# CONFIG_VIDEO_SAA6588 is not set<BR>
# CONFIG_VIDEO_CPIA is not set<BR>
# CONFIG_VIDEO_SAA5246A is not set<BR>
# CONFIG_VIDEO_SAA5249 is not set<BR>
# CONFIG_TUNER_3036 is not set<BR>
# CONFIG_VIDEO_STRADIS is not set<BR>
# CONFIG_VIDEO_ZORAN is not set<BR>
# CONFIG_VIDEO_SAA7134 is not set<BR>
# CONFIG_VIDEO_MXB is not set<BR>
# CONFIG_VIDEO_DPC is not set<BR>
# CONFIG_VIDEO_HEXIUM_ORION is not set<BR>
# CONFIG_VIDEO_HEXIUM_GEMINI is not set<BR>
# CONFIG_VIDEO_CX88 is not set<BR>
# CONFIG_VIDEO_EM28XX is not set<BR>
# CONFIG_VIDEO_OVCAMCHIP is not set<BR>
# CONFIG_VIDEO_AUDIO_DECODER is not set<BR>
# CONFIG_VIDEO_DECODER is not set<BR>
<BR>
#<BR>
# Radio Adapters<BR>
#<BR>
# CONFIG_RADIO_GEMTEK_PCI is not set<BR>
# CONFIG_RADIO_MAXIRADIO is not set<BR>
# CONFIG_RADIO_MAESTRO is not set<BR>
<BR>
#<BR>
# Digital Video Broadcasting Devices<BR>
#<BR>
# CONFIG_DVB is not set<BR>
CONFIG_VIDEO_TUNER=m<BR>
CONFIG_VIDEO_BUF=m<BR>
CONFIG_VIDEO_BTCX=m<BR>
CONFIG_VIDEO_IR=m<BR>
CONFIG_VIDEO_TVEEPROM=m
</BODY>
</HTML>