You were exactly right about the dmesg.<br>
ivtv: ==================== START INIT IVTV ====================<br>
ivtv: version 0.2.0 (rc3j) loading<br>
ivtv: Linux version: 2.6.12-gentoo-r8 preempt gcc-3.4<br>
ivtv: In case of problems please include the debug info<br>
ivtv: between the START INIT IVTV and END INIT IVTV lines when<br>
ivtv: mailing the ivtv-devel mailinglist.<br>
ivtv: Autodetected WinTV PVR 250 card<br>
ivtv: Found an iTVC16 based chip<br>
ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 217<br>
ivtv: Unreasonably low latency timer, setting to 64 (was 32)<br>
ivtv: XXX PCI device: 0x005e vendor: 0x10de<br>
tveeprom: Hauppauge: model = 32062, rev = C199, serial# = 8115353<br>
tveeprom: tuner = <unknown> (idx = 99, type = 4)<br>
tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000)<br>
tveeprom: audio_processor = MSP3445 (type = 12)<br>
ivtv: i2c attach [client=tveeprom,ok]<br>
ivtv: Tuner Type 4, Tuner formats 0x00001000, Radio: yes, Model 0x008d1659, Revision 0x00000000<br>
ivtv: NTSC tuner detected<br>
ivtv: Radio detected<br>
ivtv: Failed to load module tuner<br>
saa7115: starting probe for adapter ivtv i2c driver #0 (0x10005)<br>
saa7115: detecting saa7115 client on address 0x42<br>
saa7115: writing init values<br>
ivtv: i2c attach [client=saa7115,ok]<br>
saa7115: status: (1E) 0x00, (1F) 0xc0<br>
msp34xx: ivtv version<br>
msp34xx: init: chip=MSP3445G-B8, has NICAM support, simple (D) mode, simpler (G) no-thread mode<br>
msp34xx: $Id$ compiled on: Sep 2 2005 04:01:16<br>
ivtv: i2c attach [client=MSP3445G-B8,ok]<br>
ivtv: Encoder revision: 0x02040024<br>
ivtv: Encoder Firmware may be buggy, use version 0x02040011<br>
ivtv: Configuring WinTV PVR 250 card with 5 streams<br>
ivtv: Create DMA stream 0 using 256 16384 byte buffers 4194304 kbytes total<br>
ivtv: Registered v4l2 device, streamtype 0 minor 0<br>
ivtv: Create DMA stream 1<br>
ivtv: Registered v4l2 device, streamtype 1 minor 32<br>
ivtv: Create stream 2 using 40 52224 byte buffers 2097152 kbytes total<br>
ivtv: Registered v4l2 device, streamtype 2 minor 224<br>
ivtv: Create DMA stream 3 using 455 4608 byte buffers 2097152 kbytes total<br>
ivtv: Registered v4l2 device, streamtype 3 minor 24<br>
ivtv: Create stream 4<br>
ivtv: Registered v4l2 device, streamtype 4 minor 64<br>
ivtv: Setting Tuner 4<br>
ivtv: i2c client id: 0x02 not found!<br>
ivtv: i2c client id: 0x02 not found!<br>
saa7115: decoder set input (4)<br>
saa7115: now setting Composite input<br>
ivtv: Setting audio matrix to input 3, output 1<br>
ivtv: Switching standard to NTSC.<br>
ivtv: i2c client id: 0x02 not found!<br>
ivtv: ivtv_enc_thread: pid = 3904, itv = 0xffffffff88464c60<br>
saa7115: decoder set norm NTSC<br>
saa7115: set audio: 0x01<br>
ivtv: Initialized WinTV PVR 250, card #0<br>
ivtv: ==================== END INIT IVTV ====================<br>
<br>
I've redone the ivtv install and checked my kernel config, but can't
seem to figure this out. Since I need to get a little sleep, I
figured I'd post this and see if anyone has any ideas. Thanks for
the help!<br>