<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN">
<html>
<head>
<meta http-equiv="Content-Type" content="text/html;charset=ISO-8859-1">
<title></title>
</head>
<body text="#000000" bgcolor="#ffffff">
<big>Hi,<br>
<br>
I've setup my MythTV box following Jarod's guide up to step 13. I've
installed the driver for my PVR350 and edited /etc/modules.conf
according to Jarod's guide. However, I'm not able to tune to any
free-to-air channels in <b>Singapore</b>.<br>
<br>
This is my /etc/modules.conf :</big><br>
<br>
<tt>path[toplevel]=/lib/modules/`uname -r`/updates<br>
# default path<br>
path[toplevel]=/lib/modules/`uname -r`<br>
alias char-major-61 lirc_i2c<br>
alias usb-controller usb-ohci<br>
alias usb-controller1 ehci-hcd<br>
alias ieee1394-controller ohci1394<br>
#alias scsi_hostadapter ft3xx # Using sata_promise.o (open source
driver) now.<br>
alias scsi_hostadapter sata_promise<br>
alias eth0 nvnet<br>
alias usb-interface usb-ohci<br>
# nvidia kernel module<br>
alias char-major-195 nvidia-1.0-4363<br>
<br>
# ivtv modules setup<br>
alias char-major-81 videodev<br>
alias char-major-81-0 ivtv<br>
options ivtv ivtv_debug=1 mpg_buffers=90<br>
#options tuner type=2 # NTSC tuner<br>
options tuner type=28 # PAL tuner use type=20 or type=28<br>
options msp3400 once=1 simple=1<br>
add below ivtv msp3400 saa7115 tuner<br>
add above ivtv lirc_dev lirc_i2c<br>
<br>
#alias sound-slot-0 i810_audio<br>
# --- BEGIN: Generated by ALSACONF, do not edit. ---<br>
# --- ALSACONF verion 1.0.3 ---<br>
alias char-major-116 snd<br>
alias char-major-14 soundcore<br>
alias sound-service-0-0 snd-mixer-oss<br>
alias sound-service-0-1 snd-seq-oss<br>
alias sound-service-0-3 snd-pcm-oss<br>
alias sound-service-0-8 snd-seq-oss<br>
#alias sound-service-0-12 snd-pcm-oss dsp_map=1 adsp_map=1<br>
alias sound-service-0-12 snd-pcm-oss<br>
alias snd-card-0 snd-intel8x0<br>
alias sound-slot-0 snd-card-0<br>
# --- END: Generated by ALSACONF, do not edit. ---</tt><br>
<br>
<br>
<big>I've set my tuner type=28 according to the <b>modprobe tveeprom.</b>
<br>
<br>
<tt><small># modprobe tveeprom<br>
Warning:
/lib/modules/2.4.22-1.2174.nptl_37.rhfc1.at/updates/drivers/media/video/tveeprom.o
symbol for parameter verbose not found<br>
Module tveeprom loaded, with warnings<br>
</small></tt><br>
<br>
Following is part of the dmesg output:</big><br>
<tt>:<br>
:<br>
Linux video capture interface: v1.00<br>
i2c-core.o: i2c core module version 2.8.4 (20040207)<br>
ivtv: version 0.1.9 (release) loading<br>
ivtv: SGarray_size = 320, DSGarray_size = 16<br>
ivtv: Found an iTVC15 based chip<br>
ivtv: Unreasonably low latency timer, setting to 64 (was 32)<br>
tuner: chip found @ 0xc2<br>
saa7114.c: starting probe for adapter ivtv i2c driver #0 (0x10005)<br>
saa7114.c: detecting saa7114 client on address 0x42<br>
saa7115.c: writing init values<br>
status: (1E) 0x48, (1F) 0xc0<br>
msp34xx: init: chip=MSP3418W-A2, has NICAM support<br>
msp3410: daemon started<br>
ivtv: Encoder revision: 0x02040011<br>
ivtv: Decoder revision: 0x02020023<br>
tuner: tuner type not set<br>
ivtv: Registered v4l2 device, minor 0<br>
ivtv: Registered v4l2 device, minor 32<br>
ivtv: Registered v4l2 device, minor 224<br>
ivtv: Registered v4l2 device, minor 16<br>
ivtv: loaded<br>
lirc_dev: IR Remote Control driver registered, at major 61<br>
bttv: driver version 0.7.107 loaded<br>
bttv: using 4 buffers with 2080k (8320k total) for capture<br>
bttv: Host bridge is PCI device 10de:01e0 (nVidia Corporation)<br>
lirc_i2c: chip found @ 0x18 (Hauppauge IR)<br>
lirc_dev: lirc_register_plugin:sample_rate: 10<br>
ivtv: ivtv-api.c: unknown ioctl 0x803c7601<br>
tveeprom.c: starting probe for adapter ivtv i2c driver #0 (0x10005)<br>
tveeprom.c: detecting tveeprom client on address 0xa0<br>
9 [04] 20 77 00 40 3d 1f 65 00<br>
3 [05] 99 00<br>
8 [06] 06 bc 00 00 17 15 a9<br>
2 [07] 70<br>
Not sure what to do with tag [07]<br>
3 [09] 13 5f<br>
Not sure what to do with tag [09]<br>
3 [0a] 04 2f<br>
3 [0b] 59 8c<br>
Not sure what to do with tag [0b]<br>
2 [0e] 01<br>
2 [0f] 01<br>
Not sure what to do with tag [0f]<br>
2 [10] 01<br>
Not sure what to do with tag [10]<br>
2 [11] 00<br>
Not sure what to do with tag [11]<br>
tvee: Hauppauge: model=48134, rev=J147, serial#=6627133<br>
tvee: tuner=LG TP18PSB01D (idx=47, type=28)<br>
tvee: tuner fmt=PAL(B/G) (eeprom=0x04, v4l2=0x00000007)<br>
tvee: audio_processor=CS5331 (type=9)</tt><br>
<br>
<big>For info, Singapore is using <b>PAL B/G</b> for its' broadcasts.
I've also attempted to scan for the channels using <b>scantv -a -o
scanout</b> without any success. Note: The <b>-a</b> option causes
scantv to incremental the frequency by 0.25MHz for each iteration of
the scanning process. Following is part of the output from the
scanning:</big><br>
<br>
$ scantv -a -o scanout<br>
ioctl:
VIDIOC_ENUM_FMT(index=0;type=VIDEO_CAPTURE;flags=0;description="";pixelformat=0x00000000
[....]): Inappropriate ioctl for device<br>
<br>
please select your TV norm<br>
0: NTSC<br>
1: PAL<br>
2: SECAM<br>
nr ? 1<br>
<br>
please select a frequency table<br>
0: us-bcast<br>
1: us-cable<br>
2: us-cable-hrc<br>
3: japan-bcast<br>
4: japan-cable<br>
5: europe-west<br>
6: europe-east<br>
7: italy<br>
8: newzealand<br>
9: australia<br>
10: ireland<br>
11: france<br>
12: china-bcast<br>
13: southafrica<br>
14: argentina<br>
15: australia-optus<br>
16: russia<br>
nr ? 5<br>
invalid value for input: television<br>
valid choices for "input": "Composite 0", "Composite 1", "Composite 2",
"Composite 3", "Tuner 0", "Composite 4", "S-Video 0", "S-Video 1",
"S-Video 2", "S-Video 3"<br>
<br>
scanning freqencies...<br>
?? 44.00 MHz (- ): | no<br>
?? 44.25 MHz (- ): | no<br>
?? 44.50 MHz (- ): | no<br>
?? 44.75 MHz (- ): | no<br>
?? 45.00 MHz (- ): | no<br>
?? 45.25 MHz (- ): | no<br>
?? 45.50 MHz (- ): | no<br>
?? 45.75 MHz (- ): | no<br>
?? 46.00 MHz (- ): | no<br>
?? 46.25 MHz (- ): | no<br>
?? 46.50 MHz (- ): | no<br>
:<br>
:<br>
<br>
<big>I've tried different selections for the frequency table, all
without any success. I'll like to be able to ensure that I can tune to
all the channels before I continue with the next step of the setup. I
believe I might need to get the frequencies of all the channels and
manually enter them into the database before I can continue further.<br>
<br>
I'm at a lost on what to do next. Please help.<br>
<br>
Thanks<br>
KianTeck<big><br>
</big></big><tt><br>
</tt><tt><br>
</tt><br>
</body>
</html>