[mythtv-users] Schedules Direct DataDirect replacement service testing
Mark Perkins
perkins1724 at hotmail.com
Fri Oct 10 04:14:53 UTC 2014
> On 10 Oct 2014, at 2:09 pm, leo.butler at member.ams.org wrote:
>
> Bill Meek <keemllib at gmail.com> writes:
>
>>> On 10/09/2014 06:06 PM, leo.butler at member.ams.org wrote:
>>> Robert Eden <rmeden at yahoo.com> writes:
>>>
>>>>> On 10/2/2014 7:38 AM, Leo Butler wrote:
>>>>> Done without incident. But it was so transparent as to be invisible:
>>>>> how can I know that the json service was used? I did
>>>>>
>>>>> mythfilldatabase --dd-grad-all
>>>> The JSON service was not used, you would know if it was... you'd need to install a JSON grabber and set up lineups.
>>>>
>>>> You tested a drop-in replacement for Tribune Media Services' Data
>>>> Direct service, developed and hosted by SD. It's less efficient and
>>>> less featured than the SD JSON service, but I hope it is "good enough"
>>>> for folks that don't want (or can't) move.
>>>
>>> I have been using the new service since you made this announcement. It
>>> has worked fine for 1 source (digital cable) but not another (analog
>>> cable). I have pasted the log file at
>>>
>>> http://pastebin.com/RwCkRXFF
>>>
>>> My cable supplier (CableOne in Fargo ND) runs both a digital and an
>>> analog signal on the same line, and I have an old pvr-150 that I use in
>>> addition to an hdhr3-cc. But I haven't seen any listings or recordings
>>> for this analog service since I changed over.
>>
>> Thanks for the log.
>>
>> CoreContext datadirect.cpp:1029 (DDPost) - Downloaded 1633668 bytes
>> CoreContext datadirect.cpp:1036 (DDPost) - Uncompressed to 19477801 bytes
>>
>> That's roughly the same as I get. Robert, if you've got his data, it should
>> probably match the Uncompressed size. It doesn't appear to be a download
>> issue.
>>
>> Updating source #1 (sd-cable) with grabber schedulesdirect1
>> Found 58 channels for source 1 which use grabber
>> ...
>> Updating source #2 (sd-digitial) with grabber schedulesdirect1
>> Found 110 channels for source 2 which use grabber
>> ...
>> Updating source #3 (sd-antenna) with grabber schedulesdirect1
>> No channels are configured to use grabber. <-----------------
>> ...
>> DataDirect: Not inserting channels into disconnected source 3. <----------
>>
>> Leo, if you remove the entry in /etc/hosts and run it again, do the above lines
>> look the same?
>
> Yes. The log is at
>
> http://pastebin.com/kNgbAFr8
>
> I don't see any significant difference between the two logs, but I don't
> know what to look for...
>
>>
>> If "analog cable" = source #1 sd-cable, then it looks like it's working.
>
> Yes, sd-cable is the listing for the analog cable, and it is a mystery
> to me why it looks like it is working.
>
>> However, sd-antenna doesn't appear to be setup completely.
>
> You are correct. I would like to cut the cable cord, but haven't had
> time to set up the antenna correctly, so there are no tuners using that
> source. Sigh. Anyhow, that wasn't causing any problems with the original
> sd data and I doubt it is here, either.
>
> Robert, Bill, thanks for looking into this.
>
> Leo
> _______________________________________________
>
Sorry Leo, just to explicitly ask the question - So when you removed the entry from /etc/hosts you got all your missing listings data?
More information about the mythtv-users
mailing list