[mythtv-users] HVR-2250 - tuner unavailable
Greg
greg12866 at nycap.rr.com
Sat Apr 14 13:31:46 UTC 2012
On 04/13/2012 11:17 PM, Dan Littlejohn wrote:
>
>
> On Fri, Apr 13, 2012 at 8:55 PM, Dan Littlejohn
> <dan.littlejohn at gmail.com <mailto:dan.littlejohn at gmail.com>> wrote:
>
>
>
> On Thu, Apr 12, 2012 at 7:23 AM, Greg <greg12866 at nycap.rr.com
> <mailto:greg12866 at nycap.rr.com>> wrote:
>
> On 04/11/2012 11:02 PM, Dan Littlejohn wrote:
>
> Having trouble with the analog part of a new HVR-2250 card.
> Using
> Gentoo and kernel 3.2.1 and it looks like the card is loading ok
> (below). I downloaded the firmware and put it in
> /lib/firmware, not
> sure if that is still needed. There are /dev/video0 and
> /dev/video1
> entries and I added it using the MPEG-2 in mythtv-setup, but
> the card
> shows up on myth as "unavailable" Not sure what I need to
> look for at
> this point. I have read what I can find, does anyone have
> any tips on
> getting this to work?
>
> Dan
>
> saa7164 driver loaded
> saa7164 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
> CORE saa7164[0]: subsystem: 0070:8851, board: Hauppauge
> WinTV-HVR2250
> [card=7,autodetected]
> saa7164[0]/0: found at 0000:02:00.0, rev: 129, irq: 16,
> latency: 0,
> mmio: 0xfb800000
> saa7164 0000:02:00.0: setting latency timer to 64
> saa7164_downloadfirmware() no first image
> saa7164_downloadfirmware() Waiting for firmware upload
> (NXP7164-2010-03-10.1.fw)
> saa7164_downloadfirmware() firmware read 4019072 bytes.
> saa7164_downloadfirmware() firmware loaded.
> saa7164_downloadfirmware() SecBootLoader.FileSize = 4019072
> saa7164_downloadfirmware() FirmwareSize = 0x1fd6
> saa7164_downloadfirmware() BSLSize = 0x0
> saa7164_downloadfirmware() Reserved = 0x0
> saa7164_downloadfirmware() Version = 0x1661c00
> saa7164_downloadimage() Image downloaded, booting...
> saa7164_downloadimage() Image booted successfully.
> saa7164_downloadimage() Image downloaded, booting...
> saa7164_downloadimage() Image booted successfully.
> saa7164[0]: Hauppauge eeprom: model=88061
> DVB: registering new adapter (saa7164)
> DVB: registering new adapter (saa7164)
> saa7164[0]: registered device video0 [mpeg]
> saa7164[0]: registered device video1 [mpeg]
> saa7164[0]: registered device vbi0 [vbi]
> saa7164[0]: registered device vbi1 [vbi]
>
>
> _________________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org <mailto:mythtv-users at mythtv.org>
> http://www.mythtv.org/mailman/__listinfo/mythtv-users
> <http://www.mythtv.org/mailman/listinfo/mythtv-users>
>
>
>
> I had the same problem,it was suggested that I read over this post..
>
> http://ubuntuforums.org/__showthread.php?t=1567490&page=__10
> <http://ubuntuforums.org/showthread.php?t=1567490&page=10>
>
> I followed post #99...Thanks to Craig Cook for that...
>
>
> _________________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org <mailto:mythtv-users at mythtv.org>
> http://www.mythtv.org/mailman/__listinfo/mythtv-users
> <http://www.mythtv.org/mailman/listinfo/mythtv-users>
>
>
> minor progress on this. If I use /dev/video1 and s-video I get a
> picture,but no sound. Am using the 3.5 jack and verified it works
> with other devices, but it does not work when recording with myth.
> If I cat /dev/video1 > /tmp/test.mpg the recording is created, but
> does not have any sound. I have looked high and low for a solution
> and post #99 does not help any on this. Anyone have experience with
> this problem or a hint on what I should be looking into?
>
>
> Well, I finally figured it out. I was trying to use the adapter card
> s-video with the 3.5 jack. I could never get it to work. I finally
> found a pig tail s-video / audio adapter in the HVR-2250 box and found
> that if I used that I could get video and audio. So basically, don't
> use the adapter card. Still having a problem with having to restart
> myth several time to get the card to be usable. I will post back if I
> figure that out.
>
> Dan
>
>
>
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://www.mythtv.org/mailman/listinfo/mythtv-users
I had a very hard time getting that card to work,but since I finally
figured it out (with help) It runs great... Just a thought,are you sure
the card isn't switching nodes? Mine does on occasion...I tried to write
an udev rule to put the card on a static node,but everything I tried
doesn't seem to create the sym-link....
More information about the mythtv-users
mailing list