[mythtv-users] New Imon Kernel Driver
Stefan Manteuffel
linux at sm-recycling.de
Thu Mar 10 06:08:34 UTC 2011
Am Mittwoch 09 März 2011, 15:50:05 schrieb Jarod Wilson:
> On Mar 9, 2011, at 7:21 AM, Stefan Manteuffel wrote:
> > Hi,
> >
> > i use Myth since some years with mythbuntu.
> >
> > In my setup i had used the Lirc imon driver with two Remote Control Code
> > sets ( Logitec One) one is for the Mythfrontend and the other is for
> > switching Lights with fhem and FHT1000.
> >
> > After upgrade to Ubuntu 10.10 i must use the new iMon Kernel driver from
> > Jarod, it works very well, but i can't use the ir Codes for my Light
> > switch.
> >
> > The only solution, i found, is to use the old Lirc Module. But at the
> > next Upgrade i must reconfigure the Lirc again new. Is there a way to
> > use the new iMon Kernel driver with more ir codes ?
>
> I'm not quite sure how you were doing this to begin with[*], but if
> you were able to get more IR codes through with the old lirc driver,
> then its definitely possible to get them handled with the new imon
> driver. You'd probably have to experiment with ir-keytable to get
> additional codes recognized by the imon driver.
>
> [*] to the best of my knowledge, imon hardware only supports very
> specific IR signals, but maybe your light switch remote just happens
> to use signaling that is imon-compatible.
Hello Jarod,
and thank you for your reply. I will try to modify the ir-keytable.
Ok i have installed ir-keytables from here ppa:libv4l/ppa
but ir-keytebels -t gives me no response ?
Any hint what to do ?
Here is my OLD configuration that was working.
this is what dmesg says about my iMon:
[ 14.133877] imon 2-1.2:1.0: iMON device (15c2:0038, intf0) on usb<2:3>
initialized
[ 14.142101] imon 2-1.2:1.1: iMON device (15c2:0038, intf1) on usb<2:3>
initialized
[ 14.142120] usbcore: registered new interface driver imon
[ 20.698614] Modules linked in: nfsd exportfs nfs lockd fscache nfs_acl
auth_rpcgss snd_hda_codec_nvhdmi sunrpc nvidia(P) lirc_dev
snd_hda_codec_intelhdmi snd_hda_codec_realtek snd_hda_intel
snd_hda_codec snd_hwdep snd_pcm snd_seq_midi ir_sony_decoder snd_rawmidi
ir_jvc_decoder snd_seq_midi_event ir_rc6_decoder ppdev snd_seq ir_rc5_decoder
ir_nec_decoder rc_imon_pad
ftdi_sio snd_timer imon snd_seq_device ir_core usbserial parport_pc video
output psmouse serio_raw snd intel_agp agpgart soundcore snd_page_alloc lp
parport usbhid hid e1000e
lsusb gives me:
Bus 002 Device 003: ID 15c2:0038 SoundGraph Inc. GD01 MX VFD Display/IR
Receiver
and this is my old lircd.conf what was working with lirc and the old driver
from lirc:
------------------------------------------
# brand: licht
# model no. of remote control:
# devices being controlled by this remote:
#
begin remote
name licht
bits 16
flags SPACE_ENC|CONST_LENGTH
eps 30
aeps 100
header 4509 4492
one 599 1648
zero 599 502
ptrail 599
pre_data_bits 16
pre_data 0xC2CA
gap 111058
min_repeat 2
toggle_bit_mask 0x0
begin codes
allesaus 0xA25D
heller 0xFC03
deckenf 0x42BD
winterg 0x629D
dunkler 0xE21D
wand 0x827D
scschrank 0xC23D
tisch 0x22DD
stehlampe 0xA05F
1 0x827D
2 0x42BD
end codes
end remote
# brand: Hauppauge
# model:
# supported devices: WinTV primo; WinTV pci; WinTV radio
#
# This config file will work with both homebrew receivers and
# original Hauppauge TV cards !!!
#
begin remote
name Hauppauge
bits 13
flags SHIFT_ENC
eps 30
aeps 100
one 950 830
zero 950 830
plead 960
gap 89584
repeat_bit 2
begin codes
TV 0x000000000000100F
RADIO 0x000000000000100C
FULL_SCREEN 0x000000000000102E
CH+ 0x0000000000001020
CH- 0x0000000000001021
VOL- 0x0000000000001011
VOL+ 0x0000000000001010
MUTE 0x000000000000100D
SOURCE 0x0000000000001022
1 0x0000000000001001
2 0x0000000000001002
3 0x0000000000001003
4 0x0000000000001004
5 0x0000000000001005
6 0x0000000000001006
7 0x0000000000001007
8 0x0000000000001008
9 0x0000000000001009
0 0x0000000000001000
RESERVED 0x000000000000101E
MINIMIZE 0x0000000000001026
end codes
end remote
--------------------------------snip-------------------
and my old hardware.conf
_______________________________
#Chosen Remote Control
REMOTE="Soundgraph iMON Knob"
REMOTE_MODULES="lirc_dev lirc_imon"
REMOTE_DRIVER=""
REMOTE_DEVICE="/dev/lirc0"
#REMOTE_LIRCD_CONF="imon/lircd.conf.imon-knob"
REMOTE_LIRCD_CONF="/etc/lirc/lircd.conf"
REMOTE_LIRCD_ARGS=""
_____________________________
I must looking i while to find an ir code that works, but the i maped the key
to lamps on the Hamony remote and than maped the key to the funktions in the
fhem with irexc.
Here is a Part from ~/.lirc/licht
begin
prog = irexec
button = dunkler
repeat = 2
config = /usr/local/bin/fhem.pl 7072 "set WZ.Wand dimdown"
end
begin
prog = irexec
button = heller
repeat = 2
config = /usr/local/bin/fhem.pl 7072 "set WZ.Wand dimup"
end
begin
prog = irexec
button = stehlampe
repeat = 3
config = /usr/local/bin/fhem.pl 7072 "set WZ.Stehlampe toggle" &
end
------------------ snip
More information about the mythtv-users
mailing list