[mythtv-users] Does anyone have a working Pinnacle Hybrid USB stick ?

Paul paul at paulhurley.co.uk
Thu Dec 24 12:07:21 UTC 2009


I have a karmic mythbuntu (myth 0.22, Kernel 2.6.31-16)) running really 
well with a Hauppauge Nova-T.  I recently picked up a cheap Pinnacle 
Hybrid  Stick, and wanted to add it as a  second tuner,  mainly for 
DVB-T duties,

I plugged it in and installed the firmware and it get recognised and a 
/dev/dvb/adaptor1/ tree gets created.  It seems to use a XCeive xc2028 
chip, and reports itself as a Zarlink !.  However I added it to Myth as 
a DVB capture card with it's own XMLTV source and tried scanning for 
channels and it didn't pick anything up.  Using the card with Kaffeine 
does pick upa  few channels, although it's patchy.

Does anyone have this stick working with myth ?  Any special mojo tricks 
I should be using ?

Thanks

Paul.


lsusb
Bus 001 Device 003: ID eb1a:2881 eMPIA Technology, Inc.
Bus 001 Device 002: ID 2040:7060 Hauppauge Nova-T Stick 2

dmesg
[    7.617229] em28xx #0: i2c eeprom 00: 1a eb 67 95 1a eb 81 28 58 12 
5c 00 6a 20 6a 00
[    7.617244] em28xx #0: i2c eeprom 10: 00 00 04 57 64 57 00 00 60 f4 
00 00 02 02 00 00
[    7.617255] em28xx #0: i2c eeprom 20: 56 00 01 00 00 00 02 00 b8 00 
00 00 5b 1e 00 00
[    7.617266] em28xx #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 10 02 
00 00 00 00 00 00
[    7.617277] em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 
00 00 00 00 00 00
[    7.617288] em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 
00 00 00 00 00 00
[    7.617299] em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 
20 03 55 00 53 00
[    7.617310] em28xx #0: i2c eeprom 70: 42 00 20 00 32 00 38 00 38 00 
31 00 20 00 56 00
[    7.617321] em28xx #0: i2c eeprom 80: 69 00 64 00 65 00 6f 00 00 00 
00 00 00 00 00 00
[    7.617332] em28xx #0: i2c eeprom 90: 00 00 00 00 00 00 00 00 00 00 
00 00 00 00 00 00
[    7.617347] em28xx #0: i2c eeprom a0: 00 00 00 00 00 00 00 00 00 00 
00 00 00 00 00 00
[    7.617358] em28xx #0: i2c eeprom b0: 00 00 00 00 00 00 00 00 00 00 
00 00 00 00 00 00
[    7.617369] em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 
00 00 00 00 00 00
[    7.617380] em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 
00 00 00 00 00 00
[    7.617391] em28xx #0: i2c eeprom e0: 5a 00 55 aa 79 55 54 03 00 17 
98 01 00 00 00 00
[    7.617402] em28xx #0: i2c eeprom f0: 0c 00 00 01 00 00 00 00 00 00 
00 00 00 00 00 00
[    7.617414] em28xx #0: EEPROM ID= 0x9567eb1a, EEPROM hash = 0xb8846b20
[    7.617417] em28xx #0: EEPROM info:
[    7.617419] em28xx #0:    AC97 audio (5 sample rates)
[    7.617421] em28xx #0:    USB Remote wakeup capable
[    7.617423] em28xx #0:    500mA max power
[    7.617426] em28xx #0:    Table at 0x04, strings=0x206a, 0x006a, 0x0000
[    7.618850] em28xx #0: Identified as Unknown EM2750/28xx video 
grabber (card=1)
[    7.618854] em28xx #0: Your board has no unique USB ID.
[    7.618858] em28xx #0: A hint were successfully done, based on eeprom 
hash.
[    7.618861] em28xx #0: This method is not 100% failproof.
[    7.618863] em28xx #0: If the board were missdetected, please email 
this log to:
[    7.618866] em28xx #0:     V4L Mailing List  
<linux-media at vger.kernel.org>
[    7.618869] em28xx #0: Board detected as Pinnacle Hybrid Pro
[    7.813659] EXT4-fs (sda5): barriers enabled
[    7.819694] kjournald2 starting: pid 641, dev sda5:8, commit interval 
5 seconds
[    7.819923] EXT4-fs (sda5): internal journal on sda5:8
[    7.819928] EXT4-fs (sda5): delayed allocation enabled
[    7.819932] EXT4-fs: file extents enabled
[    7.820062] EXT4-fs: mballoc enabled
[    7.820082] EXT4-fs (sda5): mounted filesystem with ordered data mode
[    7.883485] EXT4-fs (sda10): barriers enabled
[    7.904186] kjournald2 starting: pid 652, dev sda10:8, commit 
interval 5 seconds
[    7.904433] EXT4-fs (sda10): internal journal on sda10:8
[    7.904438] EXT4-fs (sda10): delayed allocation enabled
[    7.904442] EXT4-fs: file extents enabled
[    7.928019] DVB: registering adapter 0 frontend 0 (DiBcom 7000PC)...
[    7.945847] EXT4-fs: mballoc enabled
[    7.945871] EXT4-fs (sda10): mounted filesystem with ordered data mode
[    7.989699] EXT4-fs (sda7): barriers enabled
[    8.004481] kjournald2 starting: pid 658, dev sda7:8, commit interval 
5 seconds
[    8.004501] EXT4-fs (sda7): warning: maximal mount count reached, 
running e2fsck is recommended
[    8.004726] EXT4-fs (sda7): internal journal on sda7:8
[    8.004731] EXT4-fs (sda7): delayed allocation enabled
[    8.004735] EXT4-fs: file extents enabled
[    8.006899] EXT4-fs: mballoc enabled
[    8.006919] EXT4-fs (sda7): mounted filesystem with ordered data mode
[    8.167832] tvp5150 2-005c: chip found @ 0xb8 (em28xx #0)
[    8.312440]   alloc irq_desc for 17 on node -1
[    8.312445]   alloc kstat_irqs on node -1
[    8.312454] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) 
-> IRQ 17
[    8.312508] Intel ICH 0000:00:1f.5: setting latency timer to 64
[    8.329529] MT2060: successfully identified (IF1 = 1220)
[    8.376830] tuner 2-0061: chip found @ 0xc2 (em28xx #0)
[    8.405716] xc2028 2-0061: creating new instance
[    8.405722] xc2028 2-0061: type set to XCeive xc2028/xc3028 tuner
[    8.405733] usb 1-3: firmware: requesting xc3028-v27.fw
[    8.474963] RPC: Registered udp transport module.
[    8.474968] RPC: Registered tcp transport module.
[    8.606949] SGI XFS with ACLs, security attributes, realtime, large 
block/inode numbers, no debug enabled
[    8.607579] SGI XFS Quota Management subsystem
[    8.714195] xc2028 2-0061: Loading 80 firmware images from 
xc3028-v27.fw, type: xc2028 firmware, ver 2.7
[    8.732021] intel8x0_measure_ac97_clock: measured 54779 usecs (2639 
samples)
[    8.732026] intel8x0: clocking to 48000
[    8.776017] xc2028 2-0061: Loading firmware for type=BASE (1), id 
0000000000000000.
[    8.850082] input: IR-receiver inside an USB DVB receiver as 
/devices/pci0000:00/0000:00:1d.7/usb1/1-2/input/input5
[    8.850151] dvb-usb: schedule remote query interval to 50 msecs.
[    8.850156] dvb-usb: Hauppauge Nova-T Stick successfully initialized 
and connected.
[    8.853250] usbcore: registered new interface driver dvb_usb_dib0700
[    9.025836] XFS mounting filesystem sda8
[    9.685819] Ending clean XFS mount for filesystem: sda8
[    9.824603] Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
[    9.838126] xc2028 2-0061: Loading firmware for type=(0), id 
000000000000b700.
[    9.852873] SCODE (20000000), id 000000000000b700:
[    9.852882] xc2028 2-0061: Loading SCODE for type=MONO SCODE 
HAS_IF_4320 (60008000), id 0000000000008000.
[    9.932468] XFS mounting filesystem sda9
[   10.040107] em28xx #0: Config register raw data: 0x58
[   10.040847] em28xx #0: AC97 vendor ID = 0xffffffff
[   10.041222] em28xx #0: AC97 features = 0x6a90
[   10.041225] em28xx #0: Empia 202 AC97 audio processor detected
[   10.164467] tvp5150 2-005c: tvp5150am1 detected.
[   10.268832] em28xx #0: v4l2 driver version 0.1.2
[   10.350945] em28xx #0: V4L2 device registered as /dev/video0 and 
/dev/vbi0
[   10.375101] usbcore: registered new interface driver snd-usb-audio
[   10.376869] usbcore: registered new interface driver em28xx
[   10.376875] em28xx driver loaded
[   10.822773] tvp5150 2-005c: tvp5150am1 detected.
[   11.314373] xc2028 2-0061: attaching existing instance
[   11.314378] xc2028 2-0061: type set to XCeive xc2028/xc3028 tuner
[   11.314381] em28xx #0/2: xc3028 attached
[   11.314385] DVB: registering new adapter (em28xx #0)
[   11.314390] DVB: registering adapter 1 frontend 0 (Zarlink ZL10353 
DVB-T)...
[   11.314779] Successfully loaded em28xx-dvb
[   11.314783] Em28xx: Initialized (Em28xx dvb Extension) extension
[   11.762362] type=1505 audit(1261593156.325:11): 
operation="profile_replace" pid=862 name=/sbin/dhclient3
[   11.762985] type=1505 audit(1261593156.325:12): 
operation="profile_replace" pid=862 
name=/usr/lib/NetworkManager/nm-dhcp-client.action
[   11.763323] type=1505 audit(1261593156.325:13): 
operation="profile_replace" pid=862 
name=/usr/lib/connman/scripts/dhclient-script
[   11.782151] type=1505 audit(1261593156.345:14): 
operation="profile_replace" pid=863 name=/usr/bin/evince
[   11.794907] type=1505 audit(1261593156.357:15): 
operation="profile_replace" pid=863 name=/usr/bin/evince-previewer
[   11.801036] type=1505 audit(1261593156.365:16): 
operation="profile_replace" pid=863 name=/usr/bin/evince-thumbnailer
[   11.811734] type=1505 audit(1261593156.373:17): 
operation="profile_replace" pid=865 name=/usr/sbin/mysqld
[   11.815140] type=1505 audit(1261593156.377:18): 
operation="profile_replace" pid=866 name=/usr/sbin/ntpd
[   11.820840] type=1505 audit(1261593156.385:19): 
operation="profile_replace" pid=867 name=/usr/sbin/tcpdump
[   12.068457] Ending clean XFS mount for filesystem: sda9
[   12.396915] tg3 0000:05:02.0: firmware: requesting tigon/tg3_tso5.bin
[   12.569894] tg3 0000:05:02.0: PME# disabled
[   12.874478] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   14.156427] tvp5150 2-005c: tvp5150am1 detected.
[   14.691935] tg3: eth0: Link is up at 100 Mbps, full duplex.
[   14.691940] tg3: eth0: Flow control is on for TX and on for RX.
[   14.692124] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   15.486983] type=1503 audit(1261593160.050:20): operation="open" 
pid=1136 parent=1135 profile="/usr/sbin/mysqld" requested_mask="r::" 
denied_mask="r::" fsuid=0 ouid=0 name="/sys/devices/system/cpu/"
[   17.144760] __ratelimit: 3 callbacks suppressed
[   17.144764] type=1503 audit(1261593161.709:22): operation="open" 
pid=1320 parent=1188


More information about the mythtv-users mailing list