[mythtv-users] lirc ir blaster with mce 150
captainkrypto at gmail.com
Fri May 4 22:04:48 UTC 2007
> Ok, so I am having some issues…obviously  I have a 150 MCE card
> with an IR Blaster. I can get the remote to send commands and can see them
> on irw. I have compiled the cvs version of lirc, because I could not get
> your version to compile. I am running Fedora Core 6 [2.6.20-1.2944].
> Should I try to compile the version you made for cecil? I have a Philips
> STB on Surewest cable.
> Output of dmesg | grep lirc
> lirc_mceusb2: no version for "lirc_get_pdata" found: kernel tainted.
> lirc_mceusb2: Philips eHome USB IR Transciever and Microsoft MCE 2005
> Remote Control driver for LIRC $Revision: 1.28 $
> lirc_mceusb2: Daniel Melander <lirc[at]rajidae.se>, Martin Blatter
> lirc_dev: lirc_register_plugin: sample_rate: 0
> lirc_mceusb2: Topseed eHome Infrared Transceiver on usb1:3
> usbcore: registered new interface driver lirc_mceusb2
> Output of dmesg | grep ivtv
> ivtv: ==================== START INIT IVTV ====================
> ivtv: version 0.10.1 (tagged release) loading
> ivtv: Linux version: 2.6.20-1.2944.fc6 SMP mod_unload 686 4KSTACKS
> ivtv: In case of problems please include the debug info between
> ivtv: the START INIT IVTV and END INIT IVTV lines, along with
> ivtv: any module options, when mailing the ivtv-users mailinglist.
> ivtv0: Autodetected Hauppauge card (cx23416 based)
> ivtv0: loaded v4l-cx2341x-enc.fw firmware (376836 bytes)
> ivtv0: Encoder revision: 0x02060039
> ivtv0: Autodetected Hauppauge WinTV PVR-150
> tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #0)
> cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
> wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #0)
> ivtv0: Registered device video0 for encoder MPEG (4 MB)
> ivtv0: Registered device video32 for encoder YUV (2 MB)
> ivtv0: Registered device vbi0 for encoder VBI (1 MB)
> ivtv0: Registered device video24 for encoder PCM audio (1 MB)
> ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
> ivtv: ==================== END INIT IVTV ====================
> It is not loading the firmware that you made. How can I go about getting
> it to load. Where does it need to go? Do I need to send a command to ivtv
> to tell it to use a different firmware?
> When I send a command to the irblaster with irsend it sends successfully
> but It does not blink.
> Any help would be great!!! Thanks.
> Peter Rozental
I'm not sure what the difference is between MCE and non MCE, but I followed
this guide http://www.blushingpenguin.com/mark/blog/?p=24 to get my PVR-150
non MCE version working with the IR Blaster on Fedora Core 6 (
2.6.20-1.2944.fc6). It works like a champ. My firmware is located in
/lib/firmware. Not much, but I hope that helps.
-------------- next part --------------
An HTML attachment was scrubbed...
More information about the mythtv-users