[mythtv-users] DirecTV D10-300 Serial Interface

Remco Treffkorn remco at rvt.com
Sun Aug 26 16:44:08 UTC 2007


The baudrate needs to be changed from 115200 to 9600 baud.

On Sunday 26 August 2007, Blaine Nelson wrote:
> I tried putting the port command up front as the first parameter, and
> I tried both /dev/ttyS0 and /dev/ttyS1. I did this for both serial
> outs on the back of the machine.  No luck.  Same "Error excessive
> retries" message.
>
> Any other ideas?
>
> You've got a D10-100.  Mine's a D10-300.  Maybe the software upgrade
> for the D10-300 that's supposed to make it behave like a D10-100
> doesn't do the trick any more?  Like directv has put out a newer
> version that sucks?
>
> The cable?  Could it be bad?
>
> Again, thanks for the help.  And the encouragement!
>
> On 8/25/07, George Mari <george_mythusers at mari1938.org> wrote:
> > Blaine Nelson wrote:
> > > Hi,
> > >
> > > Apologies if this post is boring and outdated.  Most of my searches on
> > > this topic have yielded posts that are more than 2 or 3 years old.
> > >
> > > Anyhow, I've been trying to get an old D10-300 satellite receiver to
> > > interface with a new install of MythTv.
> >
> > Naah! That's not old!  I have 3 DirecTV receivers - the *new* one is a
> > D10-100, hooked up to my Myth box, the other two are Hughes HIRD-E11s,
> > hooked up to my two televisions.  *Those* are old - they could pick up
> > signals from Sputnik when I first got them... ;-)
> >
> > > I've followed the
> > > instructions posted in the following:
> > >
> > >
> > > http://www.pdp8.net/directv/directv.shtml
> > > http://mythtv.org/pipermail/mythtv-users/2005-October/107586.html
> >
> > Same script I'm using to control my archaic D10-100.
> >
> > > That is,
> > >
> > > 1. I've bought and installed the serial-to-low-rate cable from
> > > http://www.dtvcontrol.com/index.aspx?content=cable.
> > > 2. I've performed the reset on the satellite box to get the updated
> > > software 3. And, tried calling directv.pl at the command line with a
> > > number of options
> > >
> > > So, for instance:
> > >
> > > blaine at blaine-desktop:/usr/local/bin$ directv.pl box_type D10-100
> > > verbose version
> > > Version 1.7
> > >
> > > blaine at blaine-desktop:/usr/local/bin$ directv.pl box_type D10-100
> > > verbose get_channel
> > > SEND: 0xFA [�] 0x87 [�]
> > > RECV: Timeout Error
> > >
> > >
> > > SEND: 0xFA [�] 0x87 [�]
> > > RECV: Timeout Error
> > >
> > >
> > > SEND: 0xFA [�] 0x87 [�]
> > > RECV: Timeout Error
> > >
> > >
> > > SEND: 0xFA [�] 0x87 [�]
> > > RECV: Timeout Error
> > >
> > >
> > > Error excessive retries
> > >
> > > blaine at blaine-desktop:/usr/local/bin$ directv.pl box_type D10-100 port
> > > /dev/ttyS1 verbose get_channel
> >
> > Did you see this text on pdp8.net page?  "If your serial cable isn't on
> > /dev/ttyS0 (com1) then use the port command to select the port, example
> > port /dev/ttyS1. The port command must at the start of the command line
> > before any command which talks to the directv box."
> >
> > You have your port command at the end of your command line, not the
> > beginning.  Try it with ttyS0 and ttyS1 if you're not sure which serial
> > port the cable is connected to on your backend.
> >
> > [deleted]
> >
> > > Should I give up on the D10-300 receiver?  Is there equipment
> > > (satellite - directv) that is easier to interface with?  Is the reason
> > > I haven't been able to find any more recent posts on this topic b/c
> > > people have moved on to newer gear?
> >
> > I think the D10 is a great settop box to interface with, primarily
> > because of the serial port.  In 2 years of operation, I've had two
> > channel change failures, one actually due to an automatic firmware
> > upgrade on the box causing the box to get in a non-responsive state.  It
> > needed a reset.  That's a lot more reliable than most people are getting
> > using IR blasters, from comments I've seen on the mailing list.
> >
> > Don't give up - I made my cable from scratch from plans on Internet
> > somewhere.  You're a step ahead with a commercially bought cable.  If
> > you have another serial port on your backend, try that as well, along
> > with different combinations of ttyS0/ttyS1 in your command line.
> > _______________________________________________
> > mythtv-users mailing list
> > mythtv-users at mythtv.org
> > http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
>
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users



-- 
Remco Treffkorn (RT445)
HAM DC2XT
remco at rvt.com   (831) 685-1201



More information about the mythtv-users mailing list