[mythtv-users] Need help configuring Pvr 150 - tuner 2-0061: tuner type not set

[Don]

Hi, I'm following Jarod's guide, but I got stuck on getting the capture 
board to work.  I ran the following test:

# /usr/bin/ivtvctl -u 0x3000
# /usr/bin/ivtvctl -p 4
# /usr/bin/ivtvctl -f width=720,height=480
# /usr/bin/ivtv-tune -c3 
# cat /dev/video0 > /tmp/test_capture.mpg  
# /usr/bin/ivtvctl -p 0 
# mplayer /tmp/test_capture.mpg 

I got either a black screen or static, depending on which input I 
selected.  I experimented with different inputs and channels, but 
nothing seems to make a difference.  I noticed a message in dmesg "tuner 
2-0061: tuner type not set", so maybe that's a clue.  I'm hoping someone 
can suggest something to try :)  Here's my dmesg and modprobe.conf.  
Thanks in advance for the help.
Don

ivtv:  ==================== START INIT IVTV ====================
ivtv:  version 0.6.2 (development snapshot compiled on Mon May  8 
07:44:41 2006) loading
ivtv:  Linux version: 2.6.16-1.2108_FC4 686 REGPARM 4KSTACKS gcc-4.0
ivtv:  In case of problems please include the debug info between
ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
ivtv:  any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [APC4] -> GSI 19 (level, 
low) -> IRQ 201
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom 2-0050: Hauppauge model 26132, rev F0B2, serial# 9399116
tveeprom 2-0050: tuner model is TCL M2523_5N_E (idx 112, type 4)
tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 2-0050: audio processor is CX25841 (idx 35)
tveeprom 2-0050: decoder processor is CX25841 (idx 28)
tveeprom 2-0050: has no radio, has IR remote
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0)
cx25840 2-0044: cx25841-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 2-0044: loaded v4l-cx25840.fw firmware (13353 bytes)
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0)
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02040024
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB 
total)
tuner 2-0061: tuner type not set
tuner 2-0061: tuner type not set
ivtv0: Initialized Hauppauge WinTV PVR-150, card #0
ivtv:  ====================  END INIT IVTV  ====================


modprobe.conf

alias eth0 forcedeth
alias snd-card-0 snd-intel8x0
options snd-card-0 index=0
options snd-intel8x0 index=0
remove snd-intel8x0 { /usr/sbin/alsactl store 0 >/dev/null 2>&1 || : ; 
}; /sbin/modprobe -r --ignore-remove snd-intel8x0
alias usb-controller ehci-hcd
alias usb-controller1 ohci-hcd
alias scsi_hostadapter sata_nv
# nvidia kernel module
alias char-major-195 nvidia-1_0-8756
alias nvidia nvidia-1_0-8756
# ivtv modules setup
alias char-major-81 ivtv
alias char-major-81-0 ivtv
#options ivtv tuner=4