[mythtv-users] Air2PC ATSC Getting it to work

Melvin J. Cureton melvincureton at MELCRYS.COM
Fri Dec 29 11:20:41 UTC 2006


The scan completed but found no services. I have a 32db HDTV RCA antenna sitting on my computer desk at the front corner of my house. Any suggestions on getting a signal.
 
Thank You
Melvin Cureton
melvincureton at melcrys.com

________________________________

From: mythtv-users-bounces at mythtv.org on behalf of Meatwad
Sent: Thu 12/28/2006 11:07 PM
To: Discussion about mythtv
Subject: Re: [mythtv-users] Air2PC ATSC Getting it to work



Melvin J. Cureton wrote:
> I have an Air2PC card installed. I have the firmware (dvb-fe-nxt2002.fw)
> in /usr/lib/hotplug/firmware. When I do dmesg I get the following:
> 
> b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded
> successfully
> flexcop-pci: will use the HW PID filter.
> flexcop-pci: card revision 2
> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18
> ACPI: PCI Interrupt 0000:01:04.0[A] -> Link [LNKB] -> GSI 18 (level,
> high) -> IRQ 201
> DVB: registering new adapter (FlexCop Digital TV device).
> b2c2-flexcop: MAC address = 00:d0:d7:30:1a:96
> b2c2-flexcop: i2c master_xfer failed
> ivtv: no version for "struct_module" found: kernel tainted.
> ivtv:  ==================== START INIT IVTV ====================
> ivtv:  version 0.8.2 (tagged release) loading
> ivtv:  Linux version: 2.6.18-1.2868.fc6 SMP mod_unload 686 REGPARM
> 4KSTACKS gcc-4.1
> ivtv:  In case of problems please include the debug info between
> ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
> ivtv:  any module options, when mailing the ivtv-users mailinglist.
> b2c2-flexcop: i2c master_xfer failed
> b2c2-flexcop: i2c master_xfer failed
> nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)
> Unknown/Unsupported NXT chip: 00 00 00 00 00
> b2c2-flexcop: i2c master_xfer failed
> lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02 error (ret == -121)
> bcm3510: Revision: 0x1, Layer: 0xb.
> b2c2-flexcop: found the bcm3510 at i2c address: 0x0f
> DVB: registering frontend 0 (Broadcom BCM3510 VSB/QAM frontend)...
> b2c2-flexcop: initialization of 'Air2PC/AirStar 2 ATSC 1st generation'
> at the 'PCI' bus controlled by a 'FlexCopIIb' complete
> 
> And with lspci -v:
> 
> 01:04.0 Network controller: Techsan Electronics Co Ltd B2C2 FlexCopII
> DVB chip / Technisat SkyStar2 DVB card (rev 02)
>         Subsystem: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip /
> Technisat SkyStar2 DVB card
>         Flags: bus master, slow devsel, latency 64, IRQ 201
>         Memory at ff4f0000 (32-bit, non-prefetchable) [size=64K]
>         I/O ports at cc00 [size=32]
> Now it say it loaded the card successfully but in ivtv it says:
> 
> b2c2-flexcop: i2c master_xfer failed
> b2c2-flexcop: i2c master_xfer failed
> nxt200x: nxt200x_readbytes: i2c read error (addr 0x0a, err == -121)
> Unknown/Unsupported NXT chip: 00 00 00 00 00
> b2c2-flexcop: i2c master_xfer failed
> Is this normal?

Is this a newer HD5000 AirStar Technisat card? If so, I get those
messages too. Doesn't seem to be a problem for me. Elsewhere in dmesg
are the lines:

   b2c2-flexcop: found the lgdt3303 at i2c address: 0x59
   DVB: registering frontend 1 (LG Electronics LGDT3303 VSB/QAM
   Frontend)...
   b2c2-flexcop: initialization of 'Air2PC/AirStar 2 ATSC 3rd generation
  (HD5000)' at the 'PCI' bus controlled by a 'FlexCopIIb' complete

If you see that, the kernel has the proper driver and you should be good
to go.

> Also, how the hell do I create a channels.conf for azap and dvbscan and
> other scanning programs? I have the attached from atennaweb.org. How do
> I change that info into a properly formatted channel.conf file. Is there
> a template or layout directions somewhere?

I just do a complete scan after properly configuring mythsetup
with a data source.
_______________________________________________
mythtv-users mailing list
mythtv-users at mythtv.org
http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users


-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://mythtv.org/pipermail/mythtv-users/attachments/20061229/8569fa3a/attachment-0001.htm 


More information about the mythtv-users mailing list