[mythtv-users] No sound from WinTV in FC5
Dave
mythtv at schooler.net
Fri Aug 11 18:19:57 UTC 2006
Good morning, all. I'm still fighting my upgrade to FC5, and am out of
ideas again.
mythtv and tvtime both have sound when I boot into FC4, but not when I
boot into FC5 (separate drives on the same box, my FC4 drive is dying,
and FC5 is a fresh install on a new drive). "aplay" does produce sound,
along with everything else I've tried besides mythtv and tvtime. I
think I've narrowed it down to the actual output from the WinTV card (as
opposed to the sound card) - when I plug speakers into the WinTV card
output, I get sound in FC4, and none in FC5.
My WinTV card says, "model 400" on the box.
I've uninstalled ivtv (I think it's not for my WinTV card). I have all
yum updates up-to-date, except for the kernel (I'm running
2.6.17-1.2157_FC5). mythtv is version 0.19, release 130.fc5.at.
The following lsmod seems relevant, but it's over my head:
[root at dave ~]# lsmod | grep bt
bt878 9416 0
snd_bt87x 13156 0
snd_pcm 75012 4
snd_bt87x,snd_intel8x0,snd_ac97_codec,snd_pcm_oss
bttv 171124 1 bt878
video_buf 23556 1 bttv
ir_common 27524 1 bttv
compat_ioctl32 1280 1 bttv
i2c_algo_bit 8905 1 bttv
btcx_risc 4488 1 bttv
tveeprom 13072 1 bttv
snd 51044 13
snd_bt87x,snd_intel8x0,snd_ac97_codec,snd_seq_dummy,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
snd_page_alloc 8456 3 snd_bt87x,snd_intel8x0,snd_pcm
i2c_core 22209 7
i2c_sis96x,tuner,tvaudio,msp3400,bttv,i2c_algo_bit,tveeprom
videodev 20992 1 bttv
v4l2_common 20608 4 tuner,msp3400,bttv,videodev
[root at dave ~]#
The same goes for a dmesg output:
[root at dave ~]# dmesg | grep bt
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 2) at 0000:00:0c.0, irq: 169, latency: 32, mmio:
0xdc12a000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: Hauppauge (bt878) [card=10,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
bttv0: Hauppauge eeprom indicates model#61351
bttv0: using tuner=8
bttv0: i2c: checking for MSP34xx @ 0x80... found
msp3400 0-0040: MSP3430G-A1 found @ 0x80 (bt878 #0 [sw])
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... not found
tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw])
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
bt878: AUDIO driver version 0.0.0 loaded
bttv0: PLL can sleep, using XTAL (28636363).
[root at dave ~]#
Does anyone have any more ideas?
Thanks!
Dave
More information about the mythtv-users
mailing list