[mythtv-users] pvr-150 error

Frank Armstrong farmstrong at gmail.com
Tue Apr 18 00:06:54 UTC 2006


this is what i find in between the lines...not sure what all this means...

ivtv:  ========== START INIT IVTV ==========
ivtv:  version 0.6.1 (development snapshot compiled on Wed Mar 29 19:14:09
2006) loading
ivtv:  Linux version: 2.6.16-1.2080_FC5 SMP gcc-4.1
ivtv:  In case of problems please include the debug info between
ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
ivtv:  any module options, when mailing the ivtv-users mailinglist.
cx2388x v4l2 driver version 0.0.5 loaded
cx2388x dvb driver version 0.0.5 loaded
eth0: forcedeth.c: subsystem: 010de:cb84 bound to 0000:00:0a.0
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20
GSI 19 sharing vector 0xC9 and IRQ 19
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCJ] -> GSI 20 (level, low) ->
IRQ 19
PCI: Setting latency timer of device 0000:00:04.0 to 64
nvidia: module license 'NVIDIA' taints kernel.
intel8x0_measure_ac97_clock: measured 58531 usecs
intel8x0: clocking to 46955
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40
ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
GSI 20 sharing vector 0xD1 and IRQ 20
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC1] -> GSI 16 (level, low) ->
IRQ 20
ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
tveeprom 2-0050: Hauppauge model 26052, rev C185, serial# 2882909
tveeprom 2-0050: tuner model is TCL 2002N 6A (idx 85, type 50)
tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 2-0050: audio processor is CX25843 (idx 37)
tveeprom 2-0050: decoder processor is CX25843 (idx 30)
tveeprom 2-0050: has no radio, has IR remote
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0)
cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
sd 2:0:0:0: Attached scsi generic sg0 type 0
sd 3:0:0:0: Attached scsi generic sg1 type 0
cx25840 2-0044: loaded v4l-cx25840.fw firmware (13353 bytes)
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #0)
ieee1394: Initialized config rom entry `ip1394'
firmware_loading_store: unexpected value (0)
ivtv0: unable to open firmware v4l-cx2341x-enc.fw
ivtv0: did you put the firmware in the hotplug firmware directory?
ivtv0 warning: failed loading encoder firmware
ivtv0 warning: Error loading firmware -3!
ivtv0: Error -3 initializing firmware.
ivtv0: Error -12 on initialization
ivtv: probe of 0000:01:07.0 failed with error -12
ivtv:  ==========  END INIT IVTV  ==========

On 4/17/06, Carl Fongheiser <carlfongheiser at gmail.com> wrote:
>
> On 4/17/06, Frank Armstrong <farmstrong at gmail.com> wrote:
>
> > i d/l the ivtv driver...according to the walkthrough....but when i try
> > to do this part...
> > # /usr/bin/ivtvctl -u 0x3000
> >
> > i get this
> >
> > not an ivtv driver device!
> > ioctl VIDIOC_S_STD ok
> > Standard set to 00003000
> >
> > then when i do this...
> >
> > # /bin/dmesg |grep Initialized
> >
> > i get this...
> >
> > ieee1394: Initialized config rom entry `ip1394'
> >
> > it sees my pvr 150 on the pci bus...but when i try to test capture
> > there's and I/O error...any help with this would be appreciated.
> >
>
>
> What's in your dmesg output between the lines "========== START
> INIT IVTV ==========" and "==========  END INIT IVTV
> =========="?  That would be the place to start.  If you don't have
> those lines, then ivtv didn't get loaded.
>
> Carl Fongheiser
>
>
>
> _______________________________________________
> mythtv-users mailing list
> mythtv-users at mythtv.org
> http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://mythtv.org/pipermail/mythtv-users/attachments/20060417/eb410619/attachment.htm 


More information about the mythtv-users mailing list